"Installed new compressor, process valve and drier. Vacuumed system for 30min. Recharge system with correct amount of refrigerant 68 grams R600a.

"pulled unit out and checked voltage and had 121 volts coming to unit , checked connections on main board and all were good , plugged unit back in and it powered up and is working now

"EC 40 & 50 codes are back again , called Sub-Zero and went through thermister readings and all are good , air flow is good through cond. coil and I just replaced it , Mr or Mrs. Hyde to advise on unit ,

"Found fan not working Mr. is going to talk to neighbor who is reimbursing him for the charges to discuss whether or not they want to continue with the repairs. If he does call the office, please order the icemaker and the fan behind the icemaker as neither one of them are working"

Found water tank magnets bad customer to order her own replacement tank recall of service per DB.

Found unit with failed ice maker module will need new module installed tested ch3cked ok

Installed repair kit tested ch3cked ok

"Installed new harnesses per tech line instruction, tested unit unit tested good advised Mr. to call us if he has any issues"

I replaced the damaged board with new part and all ops and components tested good without faults or errors. Job complete

Pulled unit out of wall checked power and no power on black side of incoming line. New boards needed for repair after cust gets power fixed by electrician customer will advise

Unit needs new hub and suspension. Could not get wash plate off. Customer decided to replace unit. Job complete.

"Found faulty, door switch, I removed and replaced it. All functions checked OK. Job complete.

Tech checked unit and found ice stuck in flap of ice bucket . Tech removed obstruction. Tested unit all checks good.

Tech replaced noisy valve . Tested unit all checks good

Installed new suspension rods and put unit into a deep fill and seen cam shield was still a inch or two inches from floor with no clothes so raised feet all the way up and made shims for front right peg and left back foot as there is a off balance of the floor and put unit into a high spin and confirmed unit working like it should and advised customer they will see more of a shake as the stabliazation is not the same as before

Unit has many issues and customer is going to get another unit

Found bad slider assy causing noise and unit not to spin out properly removed and replaced slider all ops test ok.

"Installed all new parts and tested unit. Unit is heating properly now. Job complete.

"Customer concerned that the unit is smoking. Confirmed issue. Upon arrival, tried running the unit on a 30 second cycle with water inside the unit. Could hear a very loud popping noise coming from inside the unit and can smell smoke. Immediately stopped the unit. Removed wave guide cover and inspected, found no sign of burning in the wave guide. Will need to do high voltage rebuild on the unit to get it back to safe condition. Quoted customer for repair. Customer declining repair at this time and will be getting new unit.

"Customer concerned that the unit is making a loud buzzing noise and not heating. Noise coming from magnetron. Need rebuild on high voltage components. Quoted customer for repair. Customer declining repair at this time and getting new unit.

"Replaced parts listed, unit still has a slight remaining tapping noise during operation that appears to be coming from roller shafts. Sanded them down slightly and the noise got better but is still there. Customer will call and advise if she would like us to order roller shafts, if she does call please order all 4 just in case.

"VERIFIED UNIT IS WITHIN 5 YEARS OLD WITH ENTITLEMENT PAGE. BILL WPL FOR P&L USING S CODE S191AQ. Customer concerned that the interior lights are not working. Confirmed issue. Found service pointer for this issue. Installed new LED kit, all lights are now working.

"Microwave has blow 20amp ceramic fuse in filter board,

We installed the Magnatron and inverter board. All functions check OK. Job complete.SR#7738159670

"Installed new compressor and recharged with 53g of r600 a, advised mrs to call us back if she has any issues

Inspected unit and found no visible trace of dye unit is cooling properly and holding steady at 34? per the customer settings advised Mr. to call us back if unit fails

"Found intermittent illumination, tone and function of the HMI panel. Per the customer, following last service the unit had been fully functional through multiple wash cycles prior to unrelated electrical service repairs being conducted at the homes circuit breaker panel. Power to the unit cycled at the home circuit panel. After restoring power to the unit all operations had resumed as normal and without fault. Operational issue as found likely due to a communications fault generated during power interruptions. Customer to continue normal use of the unit and advise should further repair service be required."

"Upon arrival found the unit pulled from its original install position. Prior to calling for service the customer had confirmed proper water pressure supplied to the unit and both water supply hoses clear of obstruction. Customer had removed the water restrictor's from both the hot and cold inlet water valve assemblies in attempt to correct however, with no change. F8-E1 (No Fill, Slow Fill), F5-E2 (Lock Failure) & F0-E2 (Oversuds) recorded in your history, cleared prior to testing. Unit ran through manual load testing in diagnostics finding little to no water flow through the units number one cold water inlet valve solenoid. All other unit tests and operations check good through testing. New dual cold side inlet water valve supplied by the customer and single hot side inlet water valve supplied by pre-ID installed to correct. Unit ran through complete diagnostic testing now without fault and/or water leaks. All unit test and operations check good upon completion of repair. Customer to advise.

"Upon arrival found the HMI consul unresponsive, no illumination, tone and/or function. Found only the drum interior light functional. Confirmed 240VAC properly supplied and standing at the units terminal block. Binary flash of the ACU processor LED checks good. Confirmed all HMI / ACU connections secure. Power cycle conducted after which HMI function was restored. F2-E2 (HMI Disconnected) & F2-E1 (HMI Stuck Button) recorded in unit history, cleared prior to testing. Advancement through diagnostic testing attempted however the HMI froze in process and failed to respond. Unable to advance and/or exit diagnostic program. Power cycle again conducted however, all attempts to initiate cycle operations continue to fail both in diagnostics and normal cycle selection(s). No less than a new HMI panel will be needed to correct primary failure found. Unable to conduct full component testing do the primary failure. Customer has been advised, additional component failures may exist. Customer will be contacting Maytag Customer Support in attempt to obtain Special Concession covering both Parts & Labor. Quote listed is for estimate only. No parts to be ordered without authorization. Customer to advise.

"unit flashing U1e and 202 in display , compressor not running or fans , called tech support and controls are N.L.A. NO FIX"

Got to this unit to find the vent restricted. Discuss with customer that the unit vent system needs to be cleaned to prevent excessive dry times and overpower consumption. Determine the ductwork to be the responsible factor here. Customer to get ductwork cleaned. Job complete.

"Got back to see slightly inconsistent temperatures. Found a bit of a gap between inner and outer cabinets on this unit. Due to this used adhesive to seal these up so that the unit can regulate temperature more efficiently. Believe this is part of the issue with the icemaker, not producing as fast as customer would norm see. Also gave customer information about how the door switch affects the productivity of this icemaker. Customer understood and going to make whatever actions necessary to try to help with the situation.

Got to the unit and replace parts that were ordered. Watch to see that the unit achieved a proper frost pattern before covering the evaporator back up. Had to relocate the temperature sensor to correct position and attached properly. Job complete.

Removed and replaced igniter all ops test ok.

Cx complaint: frost build up on freezer ceiling. Found an air gap on the freezer gasket on the left side near the bottom. Heated the gasket and reshaped the seal. Advised cx to leave the freezer close for 45 minutes to let the gasket set. Advised cx to call back if frost up persists.

Replaced defective cold water valve. Ran a quick test to confirm operations. Unit operates as designed.

"Cx complaint: not enough water during cycle.Entered diag, found no error codes. Ran a diag test cycle successfully. Checked for error codes again and found none. Had the cx load the unit and start a cycle. Advised cx to adjust the settings within any given cycle to get the desired water levels (recommended max deep fill, max soils, and no extra power) Found unit operating as designed."

Ran diagnostics on test 56 E05 error bad thermister shut power off to unit installed new icemaker powered back up ran diagnostics again icemaker passed ran test 45 fill was good no overflow issues temps are good in freezer section

Installed parts unit drying and heating

"Got to the unit to confirm. Fault code D 26. I called tech-support about not being able to find D 26 fault code in text sheet. Tech-support states D fault codes are coin reader errors. Entered unit into diagnostics and reset controls. Enter dryer into test mode and confirmed dryer runs and heats properly. I dont have any quarters to test out the coin mechanism and unable to locate anybody with a key to the coin box. Protect support issue should be resolved . Was given Sr#7738163183 for documentation. If issue returns, coin, reader WPW10133242 will need to be ordered and replaced."

"VERIFIED UNIT IS WITHIN MANUFACTURER WARRANTY WITH POP. REFER TO QUICK PICS. Customer concerned that the unit will thaw out at night and freezer during the day. Upon arrival, freezer temperature at 8 degrees but customer has no food in it. Checked evaporator and evaporator has full frost pattern. Entered diagnostics and checked all thermistors and they pass. Checked condenser fan and compressor and they both turn on. Evaporator fan turns on and runs strong. Damper door in refrigerator is operating properly and all door seals look good. Put unit 8th a defrost cycle and defrost heater is working. Performed reset on unit. Suspect that since the unit is empty it is having an issue maintaining temperature during defrost. Informed customer to put some items in the freezer and keep an eye on it. Found no issues at this time. Job complete.

Part not working cust just going to use it without light but wants the dw installed . Mounted dw to cabinet job complete

Tech replaced faulty board. Tested unit all checks good

Installed drain pump tested checked ok

Installed tested checked ok

Installed wire harness and confirmed unit now put together and working like it should

Unit would not power on so i went and tested all fuses and and door switch i then checked the cycle on switch and confirmed it was working but was not clicking when pressing the button so i removed nob and unit powered right up and is heating... Customer is going to leave nob off to continune to use dryer and she is happy the unit is still working

installed new control and overlay and set clock and confirmed bake element comes on and broil element comes on... Unit is back to working like it should..

"Installed new icemaker and tested due to heater not loosening cubes and icemaker liner peeling

Tech replaced faulty compressor. Tested unit all checks good

Installed dryer repair kit. Tested operations successfully. Unit operates as designed.

Tech replaced faulty door . Tested unit all checks good

Installed cutter grid all ops ok.

Found bad door switch replaced with part from truck stock all ops ok.

"Found water turned on, when cycling hot or cold valve does not open. When turning timer to fill the timer grinds inside. Bad timer not sending power to valve. Timer is no longer available cannot repair."

Replaced defrost terminator and defrost timer. Blew out condensor coil fixed shelf for customer. Job complete

Installed new icemaker

"Found valve leaking, replaced valve all ops ok.

"I removed and replaced the lid latch. I was unable to run a factory calibration and test all functions and the unit now checks OK. Job complete.

Dryer knob cracked and wont turn on to advance so dryer wont run. Customer will find one on Amazon

"Washer had a object in pump hose blocking water from draining,I removed front of washer and then with pinch off players took hose off and removed the object,tested good afterwards

Removed and replaced eoc and temp probe tested temps all ops and temps test good

Found hole in tub replaced parts listed ck ok

"Model different than dispatch. Crack in tub, customer going to buy new one."

"Installed new part and relocated sensor to new location per service matters. All ops good.

Came to inspect unit.. both the freezer and refrigerator compartment are cooling properly. Needed to just reset and erase the code which was never erased. Job complete.

Got to the unit and installed new water inlet valve. Tested and diagnostics and found all parts of the valve are working properly. Tested on a normal cycle to ensure proper fill and progression through the wash. Saw the unit fill on warm which would designate that both warm and cold valves are giving water at the same time. no error codes given no further issues found at this time. Job complete.

"Go back to this unit and could see frost developed right around the evaporator fan on the outside of the eval cover. Believe this to be an issue with the fan specifically one of the reasons I ordered it. Replace these parts and secured the freezer section thermostat securely to the evaporator, which it was not before. Also found temperature sensor in the diffuser to not be in the correct area as well. Multiple reasons why this unit may not have been performing properly. Tried to make fixes towards success for this unit. Will have to wait sometime for this unit to regulate and get back to normal temperatures.

Complaint spray arm fell of. I found that the spray arm was still intact and perfectly fine but was disconnected from the top rack.. I reconnected the spray arm and ran the unit in diagnostics. All ops and components ran good without faults or errors.

"Found suspension rods shot, spin basket with play in it, gearcase is leaking oil and shorted out the actuator. Would need extensive repair. Not worth repair."

"Complaint no heat. I found that the unit had proper power, the fuse checked good. The heater was getting 240. But the heater coils were burnt apart. I replaced the heater and the unit started heating properly.

"Checked unit out, ran spin test with towel. No error recorded in diagnostics. Customer to record video if it happens again so a tech can hear it."

Found and replaced faulty control

Cx complaint: FC frosted over.Manually defrosted the freezer evap. Confirmed the defrost heater and thermistor check okay. Evidence of ambient air intrusion. Used HVAC tape to seal refrigerant lines and defrost drain line located at the back of the unit running up inside the cabinet. All operations check okay at this time.

Removed and replaced sump assy all ops test ok.

Installed new UI control. Confirmed proper power. Getting to fill tube heater while in run mode. Job complete.

I removed and replaced the inverter. All functions check OK. Job complete

Replaced damper assembly. New damper opened immediately and unit is cooling properly. All checks OK.

Installed tstat all ops ok.

"Vacuumed unit and charged with a factory charge. Unit is cooling, customer will advise."

"Inspected unit and determine 2 problems. One was a hot wire going to the drain pump was shorted out and not making contact to the pump therefore it was not energizing it. Repaired wire connection to the drain pump and it is now working properly. Also found the cold and hot water lines going into the unit reversed. disconnected them and reconnected them to the correct place. Customer is now getting cold and hot water when requesting it. Job complete

Replaced part listed ck ok

"Removed and replaced parts listed all ops test ok .

"Customer concerned that the unit is leaking from the left bottom near the door. Confirmed issue. Upon arrival, found unit is leaning too far forward and water is overflowing at the bottom lip of the unit. Raised the feet up on both sides to level the machine, all ops good at this time. No water leak at this time.

"Washer screeching noise when spinning ,unit has bad lower bearing part is discontinued,

"Found dryer vent crushed causing long dry times. Once vent was opened up unit has great airflow and is heating properly, all checks OK at this time.

"Installed new freezer door due to bad chute opening causing warm air to enter even after new door flap closer,tested good after"

Found door springs broken causing door to fall down. Replaced both springs and all checks OK at this time.

Replaced Evaporator fan motor assembly. New fan kicked on immediately and unit is cooling properly. All operations test OK at this time.

"Replaced clutch, slider, gearcase, and inner basket. Ran a diag verification cycle and confirmed all operations check okay. Unit operates as designed.

I removed and replaced the ordered parts. I then ran a factory calibration and tested all functions and the unit now checks ok.Job complete.

"Installed new part, tested drain pan operation and water is flowing good now.

Unit needs new pump and motor assembly. Customer has decided that they will replace unit. Job complete.

"Cx complaint: long dry times. Confirmed all operations. Unit heats, tumbles, and exhausts as designed. Advised cx to call a dryer vent company to clean the dryer vent (maintenance failed to clean vents properly)

Cx complaint: unit wont runRan a diag cycle found error codes pointing at a bad wash motor. Quoted cx to replace the wash motor. Cx declined the repair.

Removed and replaced parts listed all ops test ok.

Repaired wire going to right side of heater assy job complete

Unit has a bad trans cust wants a new washer

Installed new strike and tested unit through all testings and confirmed proper opperations

"User interface failing, customer going to order and install part himself."