Installed new main control. Tested operation of the unit and it is now cooling and working properly. Job complete.

"Go to this unit was able to discern that there were multiple lights out in this unit. Used kit and replaced lights. Tested operation of the unit, all lights are now working correctly. Job complete.

"Customer concerned that the RC is not cooling, but freezer is. Confirmed issue. Upon arrival, accessed RC evaporator and found ice buildup at evaporator. Found damage to the evaporator panel due to ice buildup. Found service pointer for this issue and sr code coverage for P & 2X L. Need to installed new evaporator panel, control, and defrost all ice at evaporator. Performed repair and tested all new components, all ops good. Job complete.

"Found waterline and power cord slapping behind unit, added a buffer on the floor between wall and fridge to prevent that from happening."

Confirmed compressor shuts off when entering diagnostic mode. Job complete.

Sr7740156243 Upon arrival checked pressures found low side at -25 high side at four ran unit through step four and called whirlpool to report findings whirlpool deemed unit nonrepairable

Installed new control and reprogrammed unit confirmed unit began operating. Advise Mrs. to monitor unit.

Installed new sliders and also leveled unit for customer. Tested operation of the unit and it doors are now closing properly. Job complete.

Got back to this unit and was able to install the control and user interface. After installation of these parts tested the unit. Unit was able to achieve temperature within very short period of time. Unit working correctly now. Job complete.

Got back to this unit perform testing and found no error codes. Unit had a full bin of ice coming from the icemaker that I had just replaced on the previous visit. The control board that we showed up with here today was a part that was necessary only if this unit was not working on return.this unit is producing and has no error codes. It is not necessary to put this part in unit is working now according to normal operation. Job complete.

Installed new ice bucket due to bad auger inside

"In the process of defrosting the evaporator, noticed that the coil was icing up as fast as I could defrost it. Using SmartHQ isolated components and verified compressor relay on main control board is stuck closed, causing the compressor to run nonstop. Gave customer estimate for main control and evaporator fan motor. Customer has decided to replace the unit."

"Removed and replaced compressor and filter drier. Verified unit held a proper vacuum and recharged with 44g R600a. Unit was on and cooling at completion of service. Advised to allow 24 hours before completely reloading unit with groceries. Customer will monitor and advise.

"Found upper drawer would not drain due to locked rotor, most likely from sitting. Freed up Rotor and filled and drained upper drawer. Customer also advised when they returned home the upper drawer was full of water without being used. Advised possible seeping water valve. Water valve for this unit is no longer available. Customer will continue to closely monitor the issue."

"Found the unit set for cooling operation off and at ambient temperature on arrival. New evaporator fan motor assembly with harness installed. All initial unit tests and operations check good upon completion of service. Customer to monitor unit temperatures, operations, sounds, etc. and advise should further service be required.

I removed and replaced the electrodes.Job complete

Removed and replaced burner assembly. Job complete

Reprogrammed HMI for model type checked ok

Found unit with normal ops since last service call cust opted out of repair to call back if issue happens again return with parts ordered if they call back

Found restricted linear cannot repair cust to buy new unit

Installed control and defrosted evap all other ops checked ok as well

"Installed checked ok

Installed tested checked ok

rebuilt door with new inner panel and replaced with new hinges and confirmed unit now shutting tighter with a better seal

Installed new control and confirmed unit working through all tests in dio... Customer is happy

Installed push to start button and i could hear motor humming so i put my leads and did middle to left and while pushing the start button the volts dropped to 6 volts and when you test middle to right and push the start button the unit goes to 238 volts so i instructed customer he needed an electrician

Installed nameplate. All checks OK.

Replaced user interface. Verified fill tube is clear and all operations test OK at this time.

"Found water leak where inlet enters tank. Gave estimate for new inlet manifold, gasket and nut. Customer declined repair and has opted to replace the unit."

Replaced main control board. Calibrated and tested unit and verified all operations check OK at this time.

Found ice buildup at base of evaporator due to drain clogged with ice about 1 inch from the opening. Most likely drain was never fully cleared as it appeared to be open when I did the service kit. Unit does appear to be going through proper defrost cycles. Cleared drain and all checks OK. Customer will monitor and advise.

Installed screw and leveled unit and confirmed customer is happy with the unit being leveled

Replaced all parts listed. All operations test OK at this time. Verified freezer is now cooling properly and door is shutting as designed.

Installed new RC evap fan motor. Tested operation of the unit it and it is now cooling properly. Job complete.

"Replaced bracket and also Mrs wanted new filter installed. All checks OK.

Found faulty front right burner and left front infinite switch. I removed and replaced both parts with new parts. All functions now check OK. Job complete.

Installed parts and unit chekced ok

"On arrival found standing water under and around the stacked unit with two heavily water saturated towels at the front left to help mitigate further migration of water. Units pulled from location and all water mopped from the area prior to full inspection. Found fur accumulation between the door bellow and door glass preventing optimal seal allowing for water leak through operation however, is not believed to be the primary source of water leak found. No physical damage i.e. rips, tears, warping, etc. of the door bellow found. With the rear panel removed further inspection conducted finding the majority of water accumulation within the cabinet interior at the front left corner beneath the dispenser assembly. All water bellow connections, water hoses, etc. check good with no presence of water. Units dispenser drawer removed finding circular cardboard seal from a plastic bottle cap had become lodged in the dispenser housing drain port to the tub assembly which would restrict water flow during water fill cycles and could result in flood condition as originally found, obstruction removed however, also later found to not be the primary cause of water leak. Unit ran through both diagnostic testing and multiple water fill cycles in all temperature settings without fault and initially without water leaks. After multiple water fill cycles water leak was confirmed to be originating from the dispenser housing assembly. Unable to conduct full inspection due to the units stacked configuration. Additional component failures may exist. No less than a new dispenser housing assembly and outer bellow retaining spring will be needed. Due to the units age, condition due to heavy use and expected cost to repair the customer has opted not to advance with further service at this time. Customer to advise.

"Tested unit, had heater error, but heater came on during test, possible that heat turned off with pump failure. Diagnostic test should have turned it back on.

Replaced frzr door and installed fill tube extension. All checks ok

Dryer vent clogged recommend vent cleaning to address issue . Standing water in dryer vent tube

Sealed evap cover assy with sealer gum air flow test great frost pattern is great adjusted food and shelf for air flow customer to advise.

Replaced control and pressure sensor and pump assy. Completed 2 full function tests and a quick wash cycle and all worked perfectly. All checks ok

Loud grinding periodically from blower and roller had flat spots. Replaced blower and rollers. All checks ok

Replaced main control and diffuser. All checks ok

Replaced fan and control. All checks ok

Control board. I removed and replaced it. All functions check OK. Job complete.

Installed tested checked ok

Install new dampers and splash shield. Perform short test and confirm unit spinning properly now. Job complete.

"Installed Icemaker and cycled, all ops ok

"When I arrived, the unit was making ice as it should and had a full container. No problems found. Job complete."

Installed all new parts. Tested operation of the unit and it is now working properly And making its normal operational noises. Job complete.

"Installed new compressor, process valve and drier filter. vacuumed system for 25min. Recharged system with correct amount of Refrigerant 53 grams R600a. Unit is now cooling and working properly. Job complete.

Install new door gasket and cooktop tested operation of the unit and it is now working properly. Job complete.

Defrosted drain line and cleared out drain in pan. Steamed line very well and tightened Shepard hook job complete

Replaced the water filter housing and the water filter. Checked operation ok job complete

Installed new heater element kit. Tested operation of the unit and it is now heating properly. Job complete.

"Installed parts, all checks okay."

"Installed parts, double tested, all checks okay.

Got back to this unit and was able to install new parts. After installing new parts tested the unit and found that the icemaker is now receiving water and is able to roll through the motions. No further issues found at this time. Temperatures were set for ice production and normal operation. Job complete.

"Tested unit multiple times and checked all relays for bad solder joints or carbon build up around the base. U it is operating as normal, cust to advise.

replaced freezer conpressor and checks ok

Installed all new parts and verified unit working properly now. Ran unit through calibration cycle and calibration passed. All ops good at this time. Job complete.

"Washer acting strange i found f7e1 and f7e7 saved in memory,installed and calibrated new actuator,tested good afterwards

"installed new unit and ice machine , put panels on and checks ok"

"Found corrosion issue reported to be superficial isolated to the brass 3/8 elbow fitting into the units inlet water supply valve. However, found est. 1' inch of standing water within the units base pan triggering flood condition energizing the unit drain pump and preventing water flow into the tank. Additionally, found multiple degraded components, hoses, seals, etc. do to the unit age and prolonged water exposure. Installation of multiple replacement components would be needed to restore full unit operation and prevent related failures. Due to the unit age, extent of damage(s) and cost to repair vs replacement cost the customer has opted not to advance with further service at this time. Customer to advise.

"New electronic control and touch panel installed. Power restored for testing. All unit tests and operations to include heating cycle function and cooktop surface light function in settings low, high and off check good upon completion of service. Customer instructed to continue normal use of the unit and advise should further service be required."

"Replaced lower harness all ops ok. Did not need control or,pump, after replacing harness unit is back to normal ops."

Inspected unit and determine the defrost ptrap was clogged and frozen. Flushed and melted ice. It is now draining properly to the drain pan. Job complete.

Reset controls and confirmed heater working properly. Advise message to call us back if she has any problems if Mrs. calls back we will replace control.

"Perform short test and found motor not running only hums. Found extremely loose mounting screw for capacitor, causing damage to capacitor terminals. Installed new capacitor and perform shortest. Confirmed motor working properly now. Job complete.

"Customer concerned that the unit will run for 5-20 minutes, then shut down. Confirmed issue. Upon arrival, checked venting and venting is short in distance and not restricted. Checked power at the terminal block and the outlet and power is slightly high at 135/135/270vac. Contacted whirlpool tech line to check with them regarding this power discrepancy. Tech line stating that this power is too high, and will cause the drive motor is over draw amperage and can shut it off. Informed customer to contact the power company regarding this voltage issue.

"Washer had f2e1 and f2e2 error codes saved in memory of control,I replaced the ui harness to main control and calibrated

Found water leaking on floor due to clogged freezer drain. Cleared drain and all checks OK.

"As reported, found the units door assembly pulled free of the hinge receivers. Confirmed no physical damage. Units door hinges reset, reinstalled and secured to correct. Customer instructed on proper procedure for pulling the unit forward for cleaning, access, service, etc. to help prevent reoccurring issue.

"Found unit runs but does not heat. Verified only 80VAC at terminal block due to partially tripped circuit breaker, most likely related to recent storms. Reset breaker and unit now runs and heats properly. All operations test OK at this time.

Found no leaks from maker water pressure is good to valve ice clumped together from not using it released ice all ops test ok

"Found unit has a bad timer, parts nla."

"Dishwasher not draining due to seed and debris in drain hose,cleared and tested ok afterwards

Found cabinet swelling causing dw door to hit cab. Dropped the feet back down and door now closes. All ops ok.

"On arrival found the unit operating at set temperature without fault and/or abnormal noise issues. Customer had presented a video taken of the reported noise issue sounding that of random tapping which may or may not have been originating from the units HV control. During inspection random tapping could be heard at and around the surrounding cabinetry along the kitchen wall likely due to expansion, contractions and/or settling. UL Warning flag on the units power cord also could create similar noise issue by tapping against the cabinet exterior and/or drywall with aid of airflow from the condenser fan motor, removed to illuminate possible origin of sound issue. Unable to duplicate abnormal noise issue at time of service. Customer instructed to monitor and advise should further service be required."

Installed new motor evap and confirmed through test 4 the coils got frosted on both sides which was not the case when i first access behind the panel... Also replaced the damper control and than the user interface... Could confirm cooler air once back together but advised customer to give unit 24 hrs and if any issues contact the office

Installed mold all ops ok.

"Found faulty bake element lower oven. I removed and replaced it. Also upper oven not heating properly due to failed relay on control board for the upper oven. Control board is available, but the overlay is no longer available. Tested lower oven functions and all tests. OK there. Job complete."

"Installed new drain pump and lower harness due to not starting or washing,tub full of water,tested good after calibration

Install new control and confirmed unit working properly

"Removed and-replaced parts listed all ops test ok customer to advise.

Replaced the refrigerator evaporator. There was a leak in the evaporator coil. Vacuumed unit down and recharged with 6oz r134a. Job complete

I removed and replaced the drive motor and timer. All functions now check OK. Job complete.

Replaced complete gas manifold. Tested and verified all burners are operational and no leaks found. All checks OK at this time. Send completed photos to customer.

Replaced ACU. Unit is now running and heating properly. All checks OK.

Installed new gasket and reformed it to fit a good seal...

"Customer concerned that the unit is dripping water into the basket continuously, causing the unit to drain on its own. Confirmed issue. Upon arrival, found F8E3 error code for overflow. Removed top panel and removed line from dispenser and found water slowly dripping past the water valve. Unit needs a new valve assembly. Quoted customer to replace water valve. Customer approved. Installed new part, tested all components including detergent pump, all ops good. Job complete."

Installed compressor checked ok

Installed checked ok

Installed new ice maker. Tested operation of the icemaker and it is now working properly and no more leaks. Job complete.

"Confirmed worn out shocks causing extreme off-balance conditions during spin. Estimate declined at this time to replace suspension kit.

Found unit with loose wire reinstalled checked ok

Unit not properly leveled. Resolved leak issue. Job complete.

"Found faulty shift actuator. I removed and replaced it with a new part from truckstop. I ran a factory calibration tested all functions, including a normal cycle and the unit now checks OK. Job job complete.