Installed part. All checks okay.

Checked unit ops found unit with shorted out buttons on touch pad advised customer about issue and gave customer price for repair customer has decided to not fix unit due to price of repairing versus buying new

Tech replaced parts listed below. Tested unit all checks good

Found pump blocked causing not to spray water adjusted and cleared all ops test ok. Recall.

"Installed parts, all checks okay.

Installed console got unit remote enabled all ops ok

Replaced rotors on both drawers job complete

Installed panel tested checked ok unit is also now set up for Wi-Fi

Replaced the middle orfice to an LP orfice the burner is now flaming at a good pace. All burners are now working properly. Job complete.

Replaced part listed ck operation ok

Replaced feet on unit and leveled properly. All checks OK.

Found maker off turned on and reset unit cycled and filled customer to advise.

Defrosted ice buildup. Install new RC evaporator cover with thermistor. Tested operation of the unit and it is cooling properly. Job complete.

Tech replaced wash motor . Tested unit all checks good .

"replaced switch kit and fuse , unit is working fine now

replaced cube size control and checks ok

Came and notice the bottom drawer front panel was snapped out so the left side as coming off..therefore causing the door not too seal all the way. I reinstalled the front drawer panel and now the door should seal smoothly at all times. Customer Ill keep an eye on it.

Installed new control board

Replaced main control/UI assembly. Programmed to personality ID # 7 for this model. Ran through a quick wash and completed without fault. All checks OK.

"Found water inlet/case break was removed causing water to fill base and throw an E15 float open fault. Mrs advised she was trying to clean the unit, reinstalled and instructed on normal use and care. Tested and verified all checks OK."

Found wheel popped out of rail. Reset adjuster and unit slides fine now. Adjusters are not broke. If it happens again adjuster kit would be needed.

Found and removed dent from cabinet causing unit to grind together

Cleared out drain line checked system cleaned condensor job complete

Spoke with Nate at tech line service pointer for this unit #w11643965 sr#7736770132 made adjustment to burner head and got ignition on both burners within 4 seconds which is acceptable range according to whirlpool

Checked unit ops found unit not turning on due to a loose connection at units power supply secured connection tested and unit is working as designed at this time. Everything checks good.

Removed and replaced door assy all ops test ook.

Replaced parts listed ck okay

Unit needs new control which is no longer available for this unit and also needs drain pump. Customer will replace unit. Job complete.

Confirmed operational failure due to a shorted monitor interlock door switch. New switch group installed to correct. All unit test and operations now check good. Customer to advise.

"With aid of the U-line service manual navigation through the diagnostics settings menu conducted. No fault codes recorded in unit history. Data logger report confirms proper defrost cycles times. Temperature average is perfectly maintained however is held at 28?F with a setpoint of 34?F. Picture of the data logger report attached for reference. All other unit tests and operations check good at time of service. U-line Technical Assistance called twice while in the home however, both calls were forwarded to voicemail. Left message with no reply after more than one hour. As detailed on page 51 of the service manual, in service mode number five, offset adjusted by -5?F to allow actual temperature to more closely match set temperature. Customer instructed to allow 48 hours for the unit to reach and maintain temperature per the new temperature offset. Customer will then monitor and advise."

"Replaced sump assembly, tested unit all ops okay. Unit filled, washed, and drained good, with no noise. Job complete"

Defrost drain was clogged cleared drain and evap trough unit checks out ok and cleaned ice from bottom of freezer liner

"Installed parts, all checks okay.

Installed pump and motor. All checks okay.

Installed new motor sump assy and removed plug from disposal RETURNED DAMAGED MOTOR SUMP ASSY TO THE OFFICE

Freezer defrost drain was clogged cleared drain unit ok

"Replaced main control with new part, tested ops, light is now fully functional, all other ops tests good job complete"

Tech replaced parts listed below . Tested unit all checks good

Tech replaced part listed below . Tested unit all checks good

Got to the unit installed new parts and found that the washer is now working properly. Ran calibration cycle as well as operating normal cycle for verification of operation. Unit ran through parts and pieces without issue. Unit is now working properly job complete

Tech replaced part listed below tested unit all checks good

"Install new door, panel and nameplate. tested operation of the unit and it is not working properly job complete.

"Installed all new parts. Tested operation of the unit and it is cooling and working properly. Job complete.

Changed the agitator. Operations tested successfully.

Tech checked unit and found damper motor stuck open from debris not allowing unit to adjust temperature in ff side. Tech removed damper motor and cleared debris reinstalled damper. Tested and checks good

"Tech replaced part below , tested unit all checks good .

Installed new main control. Tested operation of the unit and it is now working properly. Also secured the microwave from the top installation screws which were loose. Unit is now stabled as well. Job complete.

Installed element all ops ok

"Found fill line not tight all the way, tightened line all ops ok."

"Spoke to kirt at tech line, advised him that after installing control the unit locks us out and will not stay powered on when entering diags. Unit has been deemed unrepairable due to system info loss. File# 7736757821

Removed and replaced lower seal on inner panel all ops test ok.

Removed and replaced lid assy all ops test ok.called in c.c to shop.

Installed new thermal fuse under warranty

Installed new panel UI due to could not operate properly or get into diagnostics tested good afterwards

Installed new disposal and checked for leak unit operational and not leaking

"Replaced adjuster kit, all checks OK.

"Found Gearcase seized, suspension worn and retractor motor grinding. Washer side would need a complete rebuild, unit is in bad shape and definitely had a leak at one point as there is a lot of rust underneath. Customer has decided to replace the unit."

Found that the fan motor shaft was rubbing slightly against rear oven cavity wall at top portion. Shaft was not centered in the hole that it transitions through. I use the drill bit to enlarge the top portion slightly so that the fan motor shaft no longer rubs against the cavity wall. This issue was also causing the lower portion of fan blade to hit the fan shroud. I removed and replaced the fan motor after enlarging hole and tested for functions and the unit now checks OK. Job complete.

"Needs new door, lock, water, inlet, valve and bellow Customer will replace unit

"Found sealed system leak. Fixed the leak. Recharged the system. Unit operating as designed.

"Replaced shorted ice maker, component tested successfully."

Removed and replaced valve all ops test ok.

Removed and replaced parts listed all ops test ok.

Installed decal ck ok

"replaced fresh food compressor , evap. coil and checks ok

Removed and replaced the motor and blower all checks okay

Installed new blower wheel and confirmed quiet opperations ... advised customer to monitior unit

Inspected unit and determine you have an internal wire harness issue where is burned out therefore not sending power to the drain pump. Also found faulty detergent dispenser assembly. Will need the whole wire harness and also a new dispenser assembly. Gave customer a rough estimate but he decided he will purchase a new unit. job complete.

Changed UI. operations tested successfully.

New ACU & HMI controls installed. Unit ran through full diagnostic testing and initial Quick Wash cycle all without fault and/or water leaks. All unit operations check good at time of service. Customer to advise. Original ACU marked and retained for core return.

Ref was still in a -25 vacuum charged system with 64 grams of R600 good heat forming on condenser and freezer dropped by 15 degrees when I left

"Tech checked unit and found debris stuck in wash arm assemblies, tech removed both wash arms and cleaned debris . Tested unit all checks good

"Tech found unit with shorted ice maker , not allowing ice to drop into ice bin , unit would need a new ice maker to fix . , will call back to authorize ice maker repair PN: W11546935 I/M"

"Complaint water in ice bucket. Found that the water tube to the ice maker was not fully seated properly causing water to drip out into the bucket. Repositioned the tube, tested ice maker no more leaks, all other ops tested good. Job complete."

Found water line iced up for he icemaker. Melted the ice. Icemaker checked out okay.

"Complaint no ice. Customer said there was no ice coming out from either ice makers, then he unplugged the unit and plugged back in, then it started making ice normally. Possible bad control. Told customer to watch unit and advise us if the unit starts acting up again."

Found unit has bad u/I gave cust est cust to advise

Removed and replaced ui all ops test ok customer to advise.

Found 5 stored errors broke lid and missing hinge customer to replace unit.

Per customer clean down the debris in between the basket and outer tub reinstalled unit tested operation and it is working properly. job complete.

Installed new main board unit checks out ok cleaned condenser

Applied silicone to door seal to hold it in place and sealed up cabinet to liner in freezer section

Found FF drain clogged causing water to run down onto bottom and floor. Flushed and cleaned drain and all operations check OK at this time.

"Found spin basket damaged outer tub during spin and caused about a 3 hole in outer tub. Also Gearcase is leaking oil. Outer tub is no longer available so unit cannot be repaired. Mr Lofstrom is in the hospital so I could not reach him to collect the service call, spoke with office and they will give him a call tomorrow.

Removed and replaced fill line all ops test ok customer to advise.

"dryer pushed back crushing vent , dryer is heating fine , Jack to get vents cleaned"

"Checked the unit found pipes resting against the back cover. Relocated pipes to prevent rattling. Found compressor overworking, as this unit is located in the garage. Temps in the garage exceed 100 degrees which is close to maximum recommended temps for unit location. Advised cx to place a fan nearby to help air circulation."

Remove and replace the door latch. All functions check OK. Job complete.

"Tech found unit with broken evap wire harness . Tech repaired connection, tested unit all checks good

Found RR burner open. Replaced burner and checks OK. Also advised customer cooktop light is staying on due to LR infinite switch sending false signal that its on. Would need to replace LR switch (WPW10441696 cost $91.07) but customer will hold off for now. All checks OK.

"Replaced fan harness, tested unit. All ops tests good job complete.

Complaint unit not washing. Valve is filling the unit with water. But the pump is not washing. Pump is humming and getting proper voltage. Customer did not want to repair.

Installed new pump & motor. Tested operation of the unit and it is now working properly with no more water leaks. Job complete.

Install new LED light modular in the fridge for compartment. Lights are working properly. Job complete.

Found faulted thermal fuse. I removed and replaced it with a thermal kit from Truck stock. All functions check OK. Job complete.

Garbage disposal was locked up. I used the customers disposal Allen tool to free it. Tested unit OK. Job complete.

"Customer states, odor of LP gas only occurs intermittently while the units oven is in use. No odor of LP gas when the unit is not in use or using the units cooktop only. Physical inspection of the unit has found no component damages. By use of a digital combustible gas leak detector initial leak testing conducted, no gas leaks detected. Units bake burner bar checks good, all gas ports clear. All wire harness / porcelain nut connections check good and secure. With the lower interior oven panel removed confirmed proper and complete flame envelope at the bake burner bar, reinstalled prior to further testing. With the kick panel left removed for ease of access unit ran through oven cycle operations. Confirmed proper function and cycling of the bake glow bar igniter pulling 3.2A opening the dual gas safety valve within less than 30 seconds. Unit left in bake cycle operation at 350?F for more than 35 minutes with no positive gas leak(s) detected by the digital combustible gas detector. No odor of LP gas had been noticed by either the customer or myself throughout testing. *Note: No gas leaks had been found by the gas service company by use of the sudsing bubbles method during initial inspection. No *Red Tag was attached to the LP gas tank and/or appliance. Per prior unit history reports, since 09/28/21 this units broil glow bar igniter has been replaced x2, bake glow bar igniter x1, dual burner gas valve x1 . Units t-stat replaced on 01/31/18. All previously installed components operating without fault at time of service. Reported intermittent odor of gas while the oven is in use may or may not be due to off-gas not fully burned off during ignition and/or flame out as occurs through normal operation. This home is not equipped with a carbon monoxide detector as advised for homes with fuel burning appliances. Customer advised to purchase and have installed a carbon monoxide detector as per the instructions for safety. Additionally, the customer has been advised to always utilize the hood vent whenever the range is in use, as well as after use till the unit has cooled. Customer to advise.

"No binary flash faults displayed at the motor control unit. Unit ran through testing finding only the timer motor, drain pump motor and inlet water valves energized. No motor function in either spin or agitation positions. No voltage supplied from the motor control unit to the shifter. Confirmed proper function of the lid reed switch. Primary failure due to a faulty motor assembly. Operational status of the shifter cannot be confirmed until power is restored through a new functioning motor control. Due to the units age, condition and expected cost of repair, the customer has opted not to advance with repair service at this time. Customer to advise.

"Installed new fill valve due to pin hole leak,tested good afterwards,

Secured arm extension with zip ties ck ok