"Ms was not home, picked up data loggers from front porch in white box. ; O-emld tckt"

Inspected unit and determine that Ice chute on the actual door is faulty therefore not allowing ice to dispense for the ice chute assembly. We have our parts department looking into the part and they will call customer with the remaining estimate depending on the estimate customer might or might not want to get it done. Customer paid service $62.50 with credit card.; rqstng P&A on 1 Icechuteassembly (Brian Sato is looking into part)

"Found the units icemaker stripper out of home position. Ice maker cube mold and ice container both clear of water and/or ice. Mechanical ice maker manually advanced after which the ice maker completed harvest cycle to include proper water fill without fault and/or water leaks. All other unit tests and operations check good at time of service. Ordering new icemaker assembly to prevent continuing ice production failures. ; ordrng 1 W11548540 (Ice maker), dspstn on spec-tagged invntry: 1 W11548535 VALVE"

"Changed the gearcase, clutch, slider, and stator. Ran calibration and tested. Unit operates as designed.; dspstn on spec-tagged invntry: 1 W10734521 SLIDER"

I removed and replaced the console. All functions check OK. Job complete.

Found unit just running drain pump wont start a cycle replaced control ck operation ok

Inspected unit found control panel loose. Its missing a nut washer for the screw. Will need to order part.; ordrng 2 WPW10131123 (Nut washer)s

"Customer complaint unit had no cool, found that the area had a bad power outage and the power killed the start dev on the compressor. Replaced start with new part, tested unit, compressor is staying on. Customer will advise on refrigerator getting cold. Job complete. Charged 235.40 by CC. Transaction ID 478155, Autho WAU333; used 1 W10197428 (Start dev) from stock"

Tech replaced faulty evap ff fan with new one. Tested unit all checks ok. Cust paid $237.62 CK Auth# X39T93

"Wrong valve ordered will nto correct one need mullinex connections not spade ; ordrng 1 W11645245 (Valve), dspstn on spec-tagged invntry: 1 WPW10179146 VALVE-INLT"

"Installed parts, customer to advise if issue returns. All checks okay at this time."

water valve is making loud buzzing noise when icemaker fills; ordrng 1 WPW10312696 (water inlet valve) and 1 W10786952 (pressure regulator) and 1 JAYONLY (JAY ONLY)

Unit not properly defrosting. This will require additional time as both fresh food doors need to be removed in order to safely. Remove the inner shelving assembly without scratching doors.; ordrng 1 W11533213 (Control) and 1 W11291124 (FF defrost heater) and 1 W11395558 (Evaporator cover assembly)

Install back panel due to noisy vibration noise. Found loose harness in back. Also tighten that up tested good afterwards.

Replaced u/i ck operation ok

"Put in new pump assembly, tested unit out in diagnostics and regular normal cycle. No leak or faults. All ops okay. Job complete.; dspstn on spec-tagged invntry: 1 W11460945 PUMP-MOTOR"

"Found failed control, installed new one and all checks okay.; dspstn on spec-tagged invntry: 1 W11608056 ELECT CONTROL"

"Unit had a bad damper control. Replaced noisy damper with new part. Tested unit, all ops tested good. Customer will advise on any other noises. Job complete.; dspstn on spec-tagged invntry: 1 WPW10594329 CONTROL"

"Found bulkhead, torn apart will order needed; ordrng 1 W11162465 (Bulkhead)"

"Install new knobs, tested operation of each burner and they are all working properly . job complete"

Got back to the unit to install new tub springs. Got the unit apart. Swapped over the parts and pieces needed to make the change. Got the unit back together to find the unit still has vibration when tested in the garage off of the pedestal. With the new leveling fee installed. This load was with towels same as testing before. Found that once moved into the laundry room in the house on a tile floor re-checked for level. Unit is indeed level and tested. Saw better results with this test than any other. Still see some slight vibration on the final spin. Seems to be improved on this load. Customer to inform us whether or not it gets worse. need to document this with tech one. Due to the days events of work and appointments was not able to call at this time.; O-emld tckt

Small oven thermostat; ordrng 1 Need (Small oven thermostat)

helped out

"Customer has canceled service on this unit upon arrival (1 of 2). Per the customer, the unit has resumed normal operations since initially calling for service. Moreover, new wooden flooring has been laid throughout the home affectively locking the unit in position preventing removal for inspection and or repair without potential damage to the flooring. Customer will first address installation issues and advise should service be required at a later date."

Spoke with TJ at tech line verified unit has vent issue and to order vent tester for full verification if confirmed vent is issue service call will be due at time of service per whirlpool sr# 7736307245 cust refused to sign to agree part # w10106710 vent tester

Installed control all ops ok

Found faulty icemaker and water valve. I removed and replaced them both. All functions check OK. Job complete. ; dspstn on spec-tagged invntry: 1 WPW10179146 VALVE-INLT and 1 WPW10300022 ICE MAKER

Installed heater all ops ok

Test 56 throwing an E5 error code bad icemaker thermister unit needs a new icemaker; ordrng 1 W11658802 (Icemaker)

Found unit out of gas reset to install dye drier and look for leak also ck warr on sealed system. Unit has taps on it already need history on unit collected 125.00 cash; ordrng 1 Dye (Drier) and 1 Warr (Info)

"Customer mentioned there was a noise coming from inside while spinning. I spun the spin basket by hand, and did not hear anything unusual that matched her description. I entered the unit into diagnostics and no error codes were found. Also, during the high speed spin she did not hear the sound either. job complete. Auth Code $125.00 CK Auth# 9M399A"

Found head warped removed and replaced all ops test ok.

Tech found unit with faulty led board causing some lights to work in ff side not all. Tech replaced board .tested unit all checks ok. Cust paid bal of 486.47 CC Auth# 934Y4J

I removed and replaced the control. I then tested all ops and the unit now checks ok.Job complete.

Removed and replaced maker assy all ops test ok.

"I filed to set this up as a two man, need extra hands to feed lines through hinge. Reset for Friday; ordrng 1 2man (2 man)"

"Found unit not cooling properly due to badly clogged condenser coil. Cleaned coil and unit is cooling properly. Customer also stated display was cutting out intermittently, could not reproduce problem so customer will monitor and advise on that. If customer calls back for display issues may need to replace jazz board (WPW10319823). All checks OK at this time. Transaction ID 478721."

Wrong part accidentally ordered. Ordering oven bottom panel.; ordrng 1 W10777210 (Oven bottom)

"Confirmed continuing operational failure since prior repair service not due to the unit and/or component failure but the result of a power supply issue. Per the customer, the unit has been non-functional since completing a full home renovation and installation of the unit. Multimeter testing conducted finding: 244VAC between L1 & L2, 174VAC between L1 to Neutral / Ground, 70VAC between L2 to Neutral / Ground. Power supply whip isolated, finding 244VAC between L1 & L2, 120VAC between L1 to Neutral / Ground, 120VAC between L2 to Neutral / Ground, only when disconnected from the units terminal block with no load. Customer states, voltage checks conducted by the electrician had not been done under load but from the outlet only, not at the units terminal block. Confirmed the units cooktop fully operational on the L1 120VAC circuit. Confirmed all connections secure with no damage to the wire harness and/or components found. Harness connections isolated at the main control with no change in voltage readings at the terminal block. No illumination, tone and/or function of the oven control with or without the L1 and L2 lines reversed at the terminal block. Units oven control may or may not be faulty however, power supply issue will need to first be corrected before further testing can be conducted to confirm. Customer advised in detail on findings to be relayed to the electrician to better aid in corrective action to restore proper VAC as needed for unit operation. Customer to advise."

"Since prior service, F3-E3 (Water Temp Fault) continues to report. New inlet water valve assembly and mode shifter actuator installed to correct. Unit ran through complete diagnostic cycle, diagnostic load testing and initial Rinse, Drain & Spin cycle through to high-speed spin without fault and/or water leaks. All unit operations check good at time of service. Customer to advise. ; dspstn on spec-tagged invntry: 1 W11399437 PUMP and 1 W10721967 CAM"

Inspected unit and determine the damper assembly motor is faulty getting 120 VAC but will not activate so its keeping the vet closed. Will need the part to repair problem. Tried calling landlord but no answer. Tenant paid for service $125.00 with credit card. ; ordrng 1 242303001 (Damper assembly)

"Inspected unit and determine the hot wire connection. Going to the inlet water valve was loose therefore not energizing the valve, so no water was going into the unit. Repair problem by reconnecting the wire, connection tightly and securely into the solenoid of the valve. It is now energizing with 120 VAC unit is not working properly. job complete."

"Replaced all parts listed, tested unit and verified turntable is working. All checks OK."

Found bad inlet valve and filter head also missing parts for filter housing nto parts customer approved est.c.c om file ; ordrng 1 242009602 (Housing) and 1 Sh (Sh) and 1 242069701 (Cover) and 1 214983814 (Head) and 1 242252702 (Valve)

Found unit has water to line not out nto parts; ordrng 1 0000 (Valve) and 1 0000 (Check valve/ grey)

Tech was assigned as a helper;

"Nothing we can do, vent is through concrete. No charge per VS"

JK and I removed and replaced the bearing kit and heater coil. All functions test OK. Job complete.; dspstn on spec-tagged invntry: 1 5303281153 REAR BEARING KIT and 1 5300622034 COIL-HEATER

RF evap motor not working needs new evap motor and thermister; ordrng 1 Wr98r4546322 (Update module) and 1 Wr55x10025 (Sensor) and 1 Wr60x26866 (RF evap motor)

"Tech found unit with faulty ice maker tech replaced ice maker and advised cust to not change water filter until operations of ice maker are good due to no dispenser for water. Tested unit all checks ok. Cust paid remaining of 405.43 CC Auth# 3JH9H9; dspstn on spec-tagged invntry: 1 EDR3RXD1 FILTER, WATER"

"Wine cooler showing Hi temp reading,no condenser operation but fan inside and lights working,called Avalon tech support and they gave me part numbers for parts needed,allow 45mins,order parts; ordrng 1 Pawc152szbs (Main control power and display boards)"

"Found bad thermostat and unit is also rusted out underneath, customer does not want unit repaired due to condition and fear of leaks. Customer has a better Scotsman upstairs that they would like moved downstairs in place of this one. Spoke with office and setup for Wednesday with a tech/delivery to move unit downstairs.; ordrng 1 MoveUnit (Move Unit) and 1 Dolly (Dolly)"

"Installed new icemaker due to stuck in harvest icemaker,tested good,cycled and filled; dspstn on spec-tagged invntry: 1 W11546609 CONTRL-BOX and 1 W11645245 WATER VALVE"

Was unable to make it to this appointment. Other appointments ran too long. Called customer and explained. Need to reschedule ASAP.; saved tckt

Replaced case break. Still getting error not enough pulses. Per TL control board error ; ordrng 1 Need (Main control Get pop first could not provide to me)

Checked ref noise is the damper motor. Damper motor needs replaced ; ordrng 1 WPW10457601 (Damper motor)

Found fill tube out of poss leaking reposs tube ck operation ok; dspstn on spec-tagged invntry: 1 W11565638 ICEMAKER and 1 WPW10279909 VALVE-INLET

Tech was assigned as a helper;

"I got to the unit to find that the drain in the freezer section was frozen. Check to ensure that this did not have a duck bill causing this issue. Unit has the S P-trap, which is the update. Had to thaw the drain and check for water flow. Unit is now draining properly. Collected for labor and service call. Customer would like to replace the door seal on the right hand door since the gasket is cracked. Did not charge for gasket at this time. Will charge for labor and gasket on return.; ordrng 1 W10830274 (Gasket) and 1 Shipping"

"Found due to normal use and excessive angle at the weakest articulating point, the units 5/16 inch water supply line into the FC door has split nearing the lower guide chase resulting in reported water leak when actuating the water dispenser. This units FC door harness and dispenser water fill tube are a foamed-in assembly and are a non-serviceable component(s) requiring installation of a new complete FC door assembly to restore to original condition and function. Due to high cost of the FC door replacement, the customer has authorized more cost effective modifications in attempt to restore proper water dispensing while at least temporary eliminating further water leaks and/or damage to adjoining wooden cabinetry. Customer has been advised, should failure reoccur, a new FC complete door assembly installation will be needed or the water dispenser actuator pad be disabled to prevent continuing water leaks and/or damage. Customer to advise. Customer has paid in full for service performed $244.28, Check No. 1273. Transaction ID:randy.scully@gmail.com; used 1 TJ80-55 (5/16 Quick Connect) from stock"

Found channel for gasket on door damaged will order new; ordrng 1 LW10636410 (Door-white)

"Found unit not cooling properly nto defrost harness and control; ordrng 1 W11650660 (Heater assy) and 1 W11645127 (Diffuser), dspstn on spec-tagged invntry: 1 W11546935 ICEMAKER and 1 W11645245 WATER VALVE"

"egg tray hitting door , moved tray over and door is closing fine now , added a little 134A to the s-z drawer Mr. to advise on unit"

I removed the lower drawer assembly and assembled the new drawer assembly with the ordered parts. I installed new draw assembly. Job complete. ; dspstn on spec-tagged invntry: 1 W10807828 GLIDE-DRWR

"no water coming into icemaker , water valve needed; ordrng 1 wr57x33326 (water valve) and 1 S&H (shipping)"

"Tech replaced shorted compressor and repaired leaky connection at the condenser line. Recharged unit with r600 . Tested unit all checks ok. Advised cust to wait 24hrs before loading unit up to be sure of repair. ; dspstn on spec-tagged invntry: 1 876764 PROCESS VALVE 1 W11504415 COUPLER , 1 W11504431 COUPLER , 1 W11504433 COUPLER , and 1 W11504447 COUPLER"

Installed burners and cooktop tested checked ok ; dspstn on spec-tagged invntry: 1 W11171119 ELMNT-SURF

Tested new latch confirm unit still not working upon further inspection. Found that the board is completely burned out not allowing to send power anywhere advised Mrs. she is going to get a new washer.; dspstn on spec-tagged invntry: 1 W11394572 LATCH

"Found unit tripping breaker, will order needed parts; ordrng 1 W11643701 (Harness) and 1 W11513246 (Control), dspstn on spec-tagged invntry: 1 W11026785 MOTOR DRIVE and 1 W11395618 CAPACITOR"

Checked unit ops found unit compressor locked up not allowing unit to cool advised customer about issue and customer is going to buy a new refrigerator.

"Call tech line and found centrifugal switch in motor faulty needs motor and timer ; ordrng 1 279827 (Motor) and 1 WP694089 (Blower wheel), dspstn on spec-tagged invntry: 1 279838 ELEMENT 1 W10900067 CUT OFF , and 1 WPW10436303 TIMER"

"need to replace touch module , shuts off intermittenly; ordrng 1 12039082 (touch module) and 1 2manjob (2 man job)"

"Found error code for shorted OWI sensor and wash motor not running. Will start with sensor, if it doesnt fix it motor would be needed and not worth repair at that point.; ordrng 1 W11084121 (OWInsensor), dspstn on spec-tagged invntry: 1 W11085683 PUMP & SUMP and 1 W11175771 WATER VALVE"

Found unit with same E5 error code for thermistor on IM will reorder new IM and data loggers to recorded temperature ; ordrng 1 W11483482 (IM assy) and 2 123 (Data logger for freezer section and IM box)s

"Adjusted front legs to level doors tightened door handles and sealed cabinet to liner in freezer section; dspstn on spec-tagged invntry: 1 W10876191 CAM-DOOR and 1 WPW10257206 CAM-DOOR , used 1 W10841140 ( Silicone) from stock"

Found faulty ice maker will order no charge to customer for labor or part; ordrng 1 WPW10300024 (icemaker)

Installed new filter cover on unit everything checks good at this time

Installed new icemaker

Tech was assigned as a helper;

"Unit falls under Technical Service Pointer #: W11632927 Rev A. Tech replaced motor and cap causing unit not to turn on and faulty lid lock,. Tested unit all checks ok; dspstn on spec-tagged invntry: 1 W11395618 CAPACITOR and 1 W11513248 LATCH"

Found sump blocked with food removed debris advised customer not to use as was instructed but commercial or salesman instructed customer on ops and care.

"Installed heater, all checks okay.; dspstn on spec-tagged invntry: 1 W11650661 DEFROST HEATER"

"Came to install by metal wire hardness, but determine that is not the faulty. The problem with the unit is the actual main control, which is not going into an automatic defrost cycle. Will need a new board. I explained it to the customer. He understood so we will get the part ordered and I will come back to install it. We will revise the estimate when I come back.; ordrng 1 WPW10503278 (Main control)"

"Customer stated that produce in different sections has been freezing. I inquired about other items, such as eggs and or water, and she said that they were not freezing. I called Whirlpool Techline and spoke with Steve and explained the situation. He asked many questions and advised me to talk to the customer about proper loading as certain air spots or trapping cold air. He also advised to check return vents to see if they were blocked and they were not. No problems. Found with unit today per Whirlpool Techline. Job complete.Whirlpool tech line Steve SR# 7736293273; dspstn on spec-tagged invntry: 1 W11043013 VALVE and 1 WPW10300024 ICEMAKER"

Unit needs a new harness and thermister; ordrng 1 WPW10487766 (Harness) and 1 WPW10384183 (Thermister)

Inspected unit and determine the wire harness connection to the drain pump was faulty loose therefore not energizing the pump. Repair problem by reconnecting the wire connection Molex tightly and securely to the drain pump. Tested operation of the drain pump and unit. It is not working properly job complete.; dspstn on spec-tagged invntry: 1 W11399437 PUMP

"New ice maker assembly installed. Unit ran through diagnostic testing to include ice maker harvest cycle test, ice maker water fill test and ice maker thermistor test, all without fault and/or water leaks. All unit operations check good at time of service. Customer to monitor and advise. ; dspstn on spec-tagged invntry: 1 W10873791 ICEMAKER"

"Installed new compressor and recharged with 56g of r600a, advised mr to monitor unit; dspstn on spec-tagged invntry: 1 W11504415 COUPLER 1 W11504431 COUPLER , and 1 W11504433 COUPLER"

Found molex off motor reseated molex tested found kink in drain hose from builder extra line installed under sink adjusted line unit drains advised customer that line needs to be replaced as so not to kink again also she advised of rust customer to contact builder do to issue being cosmetic. ; dspstn on spec-tagged invntry: 1 W10876537 PUMP-DRAIN and 1 WPW10545278 HOSE-DRAIN

Installed parts; dspstn on spec-tagged invntry: 1 w10837274 PLATE CHUTE and 1 8201711 ADHESIVE

"Since prior service on 04/10/2023, wherein ALL frost and ice accumulation was cleared throughout the air ducts, evaporator assembly, etc., found the units sending / return air ducts again frosted over preventing proper airflow resulting in High-Temp Alarm and RC temperatures at or above 71°F. Ken with Viking tech line informed on unit history and current status. Tech line has advised the installation of a retrofit heater duct kit in attempt to prevent reoccurring condition. All frost accumulation cleared restoring proper airflow and RC cooling till the duct heater kit can be installed. This is a Service Net contract, authorization needed before part order. ; ordrng 1 016616-000 (Heater kit), states that autho needed"

"Oven ignitor bad and not heating properly,tested good afterwards, used 1 5303935066 (Ignitor) from stock"

Installed new diffuser and confirmed unit operating quietly advise Mr. to keep an ion unit

Installed new diffuser and confirmed unit operating quietly advise Mr. to keep an ion unit

Tech found unit with an unsecured Gearcase cover from manufacturer causing a knocking noise in spin. Tech dissembled Gearcase cover reinstalled ;adjusted and leveled unit. Tested unit all checks ok

"Found the units evaporator again encapsulated in heavy frost accumulation blocking all airflow resulting in reoccurring warmer FC temperatures and RC no-cool condition. Unit ran through diagnostic testing finding at no point of testing prior to and/or after power cycle was the units defrost heater circuit energized. Previously ordered HV / Dispenser UI controls, not yet received. All frost accumulation cleared from the units evaporator and RC air return duct allowing for temporary cooling. Service to be reset for part(s) installation once received. ; O-emld tckt"

Found and replaced broken fuse SSN; dspstn on spec-tagged invntry: 1 279816 CUTOFF-TML and 1 279838 ELEMENT

Tech was assigned as a helper;

"Tech cant removed washplate need 2man to return to get washplate off and put new Gearcase in .; ordrng 1 2man, dspstn on spec-tagged invntry: 1 W10754448 CLUTCH"

"Customer denied service at the door states he is getting a new set for his wife for Mothers Day; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #), dspstn on spec-tagged invntry: 1 4392067RC REPAIR-DYR"