Found bad inlet valve and filter head also missing parts for filter housing nto parts customer approved est.c.c om file ; ordrng 1 242009602 (Housing) and 1 Sh (Sh) and 1 242069701 (Cover) and 1 214983814 (Head) and 1 242252702 (Valve)

Found unit has water to line not out nto parts; ordrng 1 0000 (Valve) and 1 0000 (Check valve/ grey)

Tech was assigned as a helper;

"Nothing we can do, vent is through concrete. No charge per VS"

JK and I removed and replaced the bearing kit and heater coil. All functions test OK. Job complete.; dspstn on spec-tagged invntry: 1 5303281153 REAR BEARING KIT and 1 5300622034 COIL-HEATER

RF evap motor not working needs new evap motor and thermister; ordrng 1 Wr98r4546322 (Update module) and 1 Wr55x10025 (Sensor) and 1 Wr60x26866 (RF evap motor)

"Tech found unit with faulty ice maker tech replaced ice maker and advised cust to not change water filter until operations of ice maker are good due to no dispenser for water. Tested unit all checks ok. Cust paid remaining of 405.43 CC Auth# 3JH9H9; dspstn on spec-tagged invntry: 1 EDR3RXD1 FILTER, WATER"

"Wine cooler showing Hi temp reading,no condenser operation but fan inside and lights working,called Avalon tech support and they gave me part numbers for parts needed,allow 45mins,order parts; ordrng 1 Pawc152szbs (Main control power and display boards)"

"Found bad thermostat and unit is also rusted out underneath, customer does not want unit repaired due to condition and fear of leaks. Customer has a better Scotsman upstairs that they would like moved downstairs in place of this one. Spoke with office and setup for Wednesday with a tech/delivery to move unit downstairs.; ordrng 1 MoveUnit (Move Unit) and 1 Dolly (Dolly)"

"Installed new icemaker due to stuck in harvest icemaker,tested good,cycled and filled; dspstn on spec-tagged invntry: 1 W11546609 CONTRL-BOX and 1 W11645245 WATER VALVE"

Was unable to make it to this appointment. Other appointments ran too long. Called customer and explained. Need to reschedule ASAP.; saved tckt

Replaced case break. Still getting error not enough pulses. Per TL control board error ; ordrng 1 Need (Main control Get pop first could not provide to me)

Checked ref noise is the damper motor. Damper motor needs replaced ; ordrng 1 WPW10457601 (Damper motor)

Found fill tube out of poss leaking reposs tube ck operation ok; dspstn on spec-tagged invntry: 1 W11565638 ICEMAKER and 1 WPW10279909 VALVE-INLET

Tech was assigned as a helper;

"I got to the unit to find that the drain in the freezer section was frozen. Check to ensure that this did not have a duck bill causing this issue. Unit has the S P-trap, which is the update. Had to thaw the drain and check for water flow. Unit is now draining properly. Collected for labor and service call. Customer would like to replace the door seal on the right hand door since the gasket is cracked. Did not charge for gasket at this time. Will charge for labor and gasket on return.; ordrng 1 W10830274 (Gasket) and 1 Shipping"

"Found due to normal use and excessive angle at the weakest articulating point, the units 5/16 inch water supply line into the FC door has split nearing the lower guide chase resulting in reported water leak when actuating the water dispenser. This units FC door harness and dispenser water fill tube are a foamed-in assembly and are a non-serviceable component(s) requiring installation of a new complete FC door assembly to restore to original condition and function. Due to high cost of the FC door replacement, the customer has authorized more cost effective modifications in attempt to restore proper water dispensing while at least temporary eliminating further water leaks and/or damage to adjoining wooden cabinetry. Customer has been advised, should failure reoccur, a new FC complete door assembly installation will be needed or the water dispenser actuator pad be disabled to prevent continuing water leaks and/or damage. Customer to advise. Customer has paid in full for service performed $244.28, Check No. 1273. Transaction ID:randy.scully@gmail.com; used 1 TJ80-55 (5/16 Quick Connect) from stock"

Found channel for gasket on door damaged will order new; ordrng 1 LW10636410 (Door-white)

"Found unit not cooling properly nto defrost harness and control; ordrng 1 W11650660 (Heater assy) and 1 W11645127 (Diffuser), dspstn on spec-tagged invntry: 1 W11546935 ICEMAKER and 1 W11645245 WATER VALVE"

"egg tray hitting door , moved tray over and door is closing fine now , added a little 134A to the s-z drawer Mr. to advise on unit"

I removed the lower drawer assembly and assembled the new drawer assembly with the ordered parts. I installed new draw assembly. Job complete. ; dspstn on spec-tagged invntry: 1 W10807828 GLIDE-DRWR

"no water coming into icemaker , water valve needed; ordrng 1 wr57x33326 (water valve) and 1 S&H (shipping)"

"Tech replaced shorted compressor and repaired leaky connection at the condenser line. Recharged unit with r600 . Tested unit all checks ok. Advised cust to wait 24hrs before loading unit up to be sure of repair. ; dspstn on spec-tagged invntry: 1 876764 PROCESS VALVE 1 W11504415 COUPLER , 1 W11504431 COUPLER , 1 W11504433 COUPLER , and 1 W11504447 COUPLER"

Installed burners and cooktop tested checked ok ; dspstn on spec-tagged invntry: 1 W11171119 ELMNT-SURF

Tested new latch confirm unit still not working upon further inspection. Found that the board is completely burned out not allowing to send power anywhere advised Mrs. she is going to get a new washer.; dspstn on spec-tagged invntry: 1 W11394572 LATCH

"Found unit tripping breaker, will order needed parts; ordrng 1 W11643701 (Harness) and 1 W11513246 (Control), dspstn on spec-tagged invntry: 1 W11026785 MOTOR DRIVE and 1 W11395618 CAPACITOR"

Checked unit ops found unit compressor locked up not allowing unit to cool advised customer about issue and customer is going to buy a new refrigerator.

"Call tech line and found centrifugal switch in motor faulty needs motor and timer ; ordrng 1 279827 (Motor) and 1 WP694089 (Blower wheel), dspstn on spec-tagged invntry: 1 279838 ELEMENT 1 W10900067 CUT OFF , and 1 WPW10436303 TIMER"

"need to replace touch module , shuts off intermittenly; ordrng 1 12039082 (touch module) and 1 2manjob (2 man job)"

"Found error code for shorted OWI sensor and wash motor not running. Will start with sensor, if it doesnt fix it motor would be needed and not worth repair at that point.; ordrng 1 W11084121 (OWInsensor), dspstn on spec-tagged invntry: 1 W11085683 PUMP & SUMP and 1 W11175771 WATER VALVE"

Found unit with same E5 error code for thermistor on IM will reorder new IM and data loggers to recorded temperature ; ordrng 1 W11483482 (IM assy) and 2 123 (Data logger for freezer section and IM box)s

"Adjusted front legs to level doors tightened door handles and sealed cabinet to liner in freezer section; dspstn on spec-tagged invntry: 1 W10876191 CAM-DOOR and 1 WPW10257206 CAM-DOOR , used 1 W10841140 ( Silicone) from stock"

Found faulty ice maker will order no charge to customer for labor or part; ordrng 1 WPW10300024 (icemaker)

Installed new filter cover on unit everything checks good at this time

Installed new icemaker

Tech was assigned as a helper;

"Unit falls under Technical Service Pointer #: W11632927 Rev A. Tech replaced motor and cap causing unit not to turn on and faulty lid lock,. Tested unit all checks ok; dspstn on spec-tagged invntry: 1 W11395618 CAPACITOR and 1 W11513248 LATCH"

Found sump blocked with food removed debris advised customer not to use as was instructed but commercial or salesman instructed customer on ops and care.

"Installed heater, all checks okay.; dspstn on spec-tagged invntry: 1 W11650661 DEFROST HEATER"

"Came to install by metal wire hardness, but determine that is not the faulty. The problem with the unit is the actual main control, which is not going into an automatic defrost cycle. Will need a new board. I explained it to the customer. He understood so we will get the part ordered and I will come back to install it. We will revise the estimate when I come back.; ordrng 1 WPW10503278 (Main control)"

"Customer stated that produce in different sections has been freezing. I inquired about other items, such as eggs and or water, and she said that they were not freezing. I called Whirlpool Techline and spoke with Steve and explained the situation. He asked many questions and advised me to talk to the customer about proper loading as certain air spots or trapping cold air. He also advised to check return vents to see if they were blocked and they were not. No problems. Found with unit today per Whirlpool Techline. Job complete.Whirlpool tech line Steve SR# 7736293273; dspstn on spec-tagged invntry: 1 W11043013 VALVE and 1 WPW10300024 ICEMAKER"

Unit needs a new harness and thermister; ordrng 1 WPW10487766 (Harness) and 1 WPW10384183 (Thermister)

Inspected unit and determine the wire harness connection to the drain pump was faulty loose therefore not energizing the pump. Repair problem by reconnecting the wire connection Molex tightly and securely to the drain pump. Tested operation of the drain pump and unit. It is not working properly job complete.; dspstn on spec-tagged invntry: 1 W11399437 PUMP

"New ice maker assembly installed. Unit ran through diagnostic testing to include ice maker harvest cycle test, ice maker water fill test and ice maker thermistor test, all without fault and/or water leaks. All unit operations check good at time of service. Customer to monitor and advise. ; dspstn on spec-tagged invntry: 1 W10873791 ICEMAKER"

"Installed new compressor and recharged with 56g of r600a, advised mr to monitor unit; dspstn on spec-tagged invntry: 1 W11504415 COUPLER 1 W11504431 COUPLER , and 1 W11504433 COUPLER"

Found molex off motor reseated molex tested found kink in drain hose from builder extra line installed under sink adjusted line unit drains advised customer that line needs to be replaced as so not to kink again also she advised of rust customer to contact builder do to issue being cosmetic. ; dspstn on spec-tagged invntry: 1 W10876537 PUMP-DRAIN and 1 WPW10545278 HOSE-DRAIN

Installed parts; dspstn on spec-tagged invntry: 1 w10837274 PLATE CHUTE and 1 8201711 ADHESIVE

"Since prior service on 04/10/2023, wherein ALL frost and ice accumulation was cleared throughout the air ducts, evaporator assembly, etc., found the units sending / return air ducts again frosted over preventing proper airflow resulting in High-Temp Alarm and RC temperatures at or above 71°F. Ken with Viking tech line informed on unit history and current status. Tech line has advised the installation of a retrofit heater duct kit in attempt to prevent reoccurring condition. All frost accumulation cleared restoring proper airflow and RC cooling till the duct heater kit can be installed. This is a Service Net contract, authorization needed before part order. ; ordrng 1 016616-000 (Heater kit), states that autho needed"

"Oven ignitor bad and not heating properly,tested good afterwards, used 1 5303935066 (Ignitor) from stock"

Installed new diffuser and confirmed unit operating quietly advise Mr. to keep an ion unit

Installed new diffuser and confirmed unit operating quietly advise Mr. to keep an ion unit

Tech found unit with an unsecured Gearcase cover from manufacturer causing a knocking noise in spin. Tech dissembled Gearcase cover reinstalled ;adjusted and leveled unit. Tested unit all checks ok

"Found the units evaporator again encapsulated in heavy frost accumulation blocking all airflow resulting in reoccurring warmer FC temperatures and RC no-cool condition. Unit ran through diagnostic testing finding at no point of testing prior to and/or after power cycle was the units defrost heater circuit energized. Previously ordered HV / Dispenser UI controls, not yet received. All frost accumulation cleared from the units evaporator and RC air return duct allowing for temporary cooling. Service to be reset for part(s) installation once received. ; O-emld tckt"

Found and replaced broken fuse SSN; dspstn on spec-tagged invntry: 1 279816 CUTOFF-TML and 1 279838 ELEMENT

Tech was assigned as a helper;

"Tech cant removed washplate need 2man to return to get washplate off and put new Gearcase in .; ordrng 1 2man, dspstn on spec-tagged invntry: 1 W10754448 CLUTCH"

"Customer denied service at the door states he is getting a new set for his wife for Mothers Day; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #), dspstn on spec-tagged invntry: 1 4392067RC REPAIR-DYR"

"Refrigerator has sealed system problem and need to order parts,allow extra 1.5hrs,order parts; ordrng 1 FG4H2272UF (Filter drier)"

New FC drawer bin installed restoring proper drawer function. Customer to advise.

"Got back to the unit to disassemble all used and faulty parts. Once parts were removed, was able to get the unit back up and running with all new parts that were ordered. Tested unit to ensure function found no issues at this time. Unit back to normal.; dspstn on spec-tagged invntry: 1 W11130362 SUSP 1 W10528947 HUB , and 1 W11239857 BELT"

"I removed and replaced the control and pump and motor assembly. I tested all functions and checked for leaks and the unit now checks OK. Job complete. ; dspstn on spec-tagged invntry: 1 W11087376 PUMP&MOTOR 1 WPW10327249 VALVE-INLT , and 1 W11305296 CNTRL-ELEC"

Installed parts tested checked ok ; dspstn on spec-tagged invntry: 1 W10721967 CAM

Tech was assigned as a helper;

Replaced parts listed and all checks OK.

put on new seal and advised customer to let dry for a few hours before use; dspstn on spec-tagged invntry: 1 WP279368 ADHESIVE

"Found switching valve possibly getting stuck, will order and replace; ordrng 1 W11574310 (Switching valve) and 1 Dyedrier"

Found part came in damaged will reorder ; ordrng 1 W11343212 (Panel)

"Installed new heating element per service special project S17304,; dspstn on spec-tagged invntry: 1 w11537778 DW HEATER KIT"

7736295548 TL file number. Per TL this is a normal operating noise and this has been logged in their system. Job complete

Needs water valve assy. Water proof system. ; ordrng 1 10656630 (Water valve assy)

"Got to the unit to hear from the customer that the refrigerator section is freezing foods on the top shelf. Also, hearing from the customer that the unit is making a lot of noise when work sounds like the defrost cycle is running. Due to these complaints, took the resolution to seal up the inner and outer part of the cabinet with adhesive. Also, ordering defrost timer and thermistor for refrigeration section. These parts should resolve the temperature swing in the refrigerator section. Along with the warm air infiltration being solved the problem should rectify themselves with this resolved. Customer would like to have me come back.; ordrng 1 W11616408 (Defrost control) and 1 WPW10384183 (Thermistor) and 1 Sendmeback"

Removed and replaced cavity fan. Job complete

"replaced water line and checks ok , 475292"

Tech was assigned as a helper;

"Found the units suspension heavily worn resulting in reported out of balance load conditions, high speed spin failures and water saturated loads at end of cycle. No physical component damage(s) found throughout inspection. New suspension kit supplied by pre-ID installed to correct. Unit ran through calibration cycle, auto test and manual load testing in diagnostics now without fault and/or water leaks. All unit operations to include proper balance through high speed spin cycles check good at time of service. Customer to continue normal use and advise. Customer has paid in full $340.11: CC, Transaction ID: 476529. ; dspstn on spec-tagged invntry: 1 W10734521 SLIDER"

"Got to the unit to install new parts. However, once the control panel was removed, it was clear to see that the spring and cam had come out of the top support. Was able to put the unit back together with pieces found inside. Tested the unit to find that all parts and pieces are now working properly. Collected for labor only. Unit is now heating and working properly.; dspstn on spec-tagged invntry: 1 W10156812 SPRING 2 w10269458 SWITCHES , 2 W10727360 SWITCH , 1 WP8206419 INTERLOCK , and 1 WPW10156813 INTERLOCK"

Ordering parts; ordrng 1 W11672041 (Control) and 1 W11632709 (User interface)

"Found wash motor failed, ordering part.; ordrng 1 W11460946 (Sump and motor), dspstn on spec-tagged invntry: 1 W11434044 VALVE-INLET"

Cx canceled at the door

"Found touch pad not working on some cycles, nto console. Transaction ID: 475553; ordrng 1 WP8534833 (Console)"

"Installed compressor, vacuumed and charged with 53g of r600. All checks okay.; dspstn on spec-tagged invntry: 1 W11109499 DRIER 1 W11504416 COUPLER , 1 W11504433 COUPLER , 1 W11504445 COUPLER , and 2 W11504447 COUPLER"

confirmed shorted heating element and replaced with new one and confirmed proper heating

"Found bad infinite switch on left front burner, called techline and Chris documented it . SR#7736292463. Called safety and Sasha documented 7736273514. Customer declined estimate stating he has extended warranty.; ordrng 1 WPW10434452 (Switch)"

Found power going into inverter and nothing coming out to compressor. Nto inviter I did advise that we wont know if the compressor is good until we install inverter. Transaction ID: 475891; ordrng 1 WR49X10283 (Inverter)

Checked unit ops found unit over filling due to a faulty pressure switch on main control board ran unit in a quick wash cycle and unit is spinning and draining as designed nto main control ; ordrng 1 W11419171 (Cntrl-elec)

Tech was assigned as a helper;

Found unit with defrost issue will nto new heater defrosted unit to buy time ; ordrng 1 W11650660 (Heater assy)

"SR# 7736298324 - Found 240VAC when unit is disconnected from home power supply. As soon as unit is wired up voltage intermittently drops from 240 to 120. Possible loose connection in home wiring. Unit may have other issues, but need to verify good power before parts are replaced. Customer will advise."

Ran unit thru cycle only issue is a bad lid switch gave est 98.32 cust to advise

Fixed the broken adjusters and replaced the broken spray arm. Unit now operates as designed.; dspstn on spec-tagged invntry: 2 WPW10195840 POSITIONER

"Installed ff door, freezer door was damaged, ordering part.; ordrng 1 W11551458 (Door ss frz), dspstn on spec-tagged invntry: 1 W11223753 NAMEPLATE"

"Installed endcap, all checks okay."

Tech was assigned as a helper;

Replaced parts listed and unit is working properly.

Replaced new drain pump after sucking all water out of lines just incase there was a clog unit checks out ok; dspstn on spec-tagged invntry: 1 W11219380 PUMP-DRAIN and 1 WPW10545278 HOSE-DRAIN

Installed tested checked ok

Tech found unit with faulty evap wire harness causing unit not to defrost . Also found evap thermistor out of place which can cause bad readings. Tech defrosted unit and installed thermistor correctly. Unit still needs new updated wire harness to fix. Order parts below ; ordrng 1 W11650660 (Heater harness)

"Installed and tested new control board and thermostat,tested good afterwards ; dspstn on spec-tagged invntry: 1 W11182108 ELMNT-BAKE and 1 WPW10181986 SENSOR"

"Spoke with customer and she advised she has a Lowes Extended Warranty, she was wrongly informed we could go through that warranty, advised she will have to call Lowes back and have them dispatch out their preferred company to be able to fully utilize the extended plan."

New pump & motor assembly installed. Unit ran through complete auto test in diagnostics without fault and/or water leaks. All unit operations check good at time of service. Customer to advise.