"Installed parts,all checks okay."

"Possible issue from filter replacement, all checks okay. Customer to advise if issue returns.

Installed compressor tested checked ok

"Due to the slow nature of occurring water leak requiring an excess of one hour to trigger the units float switch resulting in displayed fault and operational failure, unable to positively identify origin. However, due to water accumulation within the base pan dividing segments, water leak is likely originating from either the wash pump motor and/or a pin holes within the lower tank as a result of rust through due to imperfections in the stainless steel alloy, which if found to be the cause would deemed the unit non-repairable. Customer has opted not to advance with further repair service as the expense to repair would likely be better served towards the purchase of a replacement unit. Customer to advise"

"Found the units drain pump impeller intermittently seizing resulting in operational failure. New drain pump assembly supplied by pre-ID installed correct. Unit ran through calibration cycle, auto test and manual load testing in diagnostics as well as initial Rinse Drain & Spin Cycle without fault and/or water leaks. All unit operations check good upon completion of repair. Customer to advise.

Installed new ice maker and confirmed valve putting in water... Advised customer to monitor unit

"Installed motor, and it fired right up. All ops ok.

Per tech line the parts needed for repair are NLA

"Refrigerator icemaker shut off,reset breaker and tested good afterwards

Freezer door rails are damaged and need to be replaced. Parts no longer available for this unit. Job complete.

User interface has a crack across several of the capacitive touch buttons causing erratic operation. Customer will replace unit.Job complete

Tech replaced faulty board. Tested unit all checks good

Replaced the main board and oven temp sensor. Tested operations successfully. Unit operates as designed

Changed the drive belt. Tested operations successfully. Unit operates as designed.

Advised customer water was turned off to unit. Showed customer where water shut off is located. All checks OK.

"Got to the unit and ran testing to find that the unit valve works properly and is sending water into the machine. Both cold and hot are working properly. This appears to be an issue of possibly not explaining the procedures quite right to the customer. This customer was unable to make the Deepwater selection, even after being informed on how to do so. This took a little extra explanation to ensure customer abilities on selecting different cycles and making the unit work for them. All testing has shown this unit is working properly and customer just needed a little more coaching to make this work the way they want and the way they need. Job complete."

"Go to this unit to find the bulb had broken off of the base portion of the bulb and was stuck in the socket of the microwave. Was able to remove the base of the bulb and install new without any damage to the socket holder. After installing new bulb found that the unit is now working properly. No further issues seen at this time. Job complete

"Worn out suspension, removed and replaced , recalibrated and ran a diagnostic test, all checks okay .

Replaced cover all checks okay

"Replaced fill tube heater, steamed out fill tube and put unit in diagnostic to manually run ice harvest and fill which completed without fault. All checks OK at this time."

"Customer woundering if the pump is clogged,I cleared the pump of debris and tested good afterwards

"Found unit temperatures and ice production have resumed as normal since initial reported failure. Inspection has found multiple bags of frozen food product at the FC lower door shelf which had been contacting and pushing against the lower FC pull out bin which very well may have been the original cause of the reported no cool condition. Additionally, the customer has also reported ice dispensing failure wherein when the ice dispenser paddle is actuated no sound and/or function occurs. Through inspection found the units auger motor failed, voltage supplied when actuated, no motor function. Due the units age of +15yrs and cost of a new auger motor replacement, the customer has opted not to advance with installation of a new auger motor but has agreed to the installation of an exact replacement auger motor from miscellaneous truck stock previously pulled from exchange. *Note: Miscellaneous motor sold at 50% savings carries a six month part warranty only. All unit test and operations check good upon completion of repair. Customer advised on presumed cause of cooling failure in attempt to prevent reoccurring issue. Customer to advise.

Installed both rollers and leveled fridge and customer is happy

"Tech checked unit and found unit with broken heater harness, tech dissembled evap cover and defrosted ice on evaporator. Tech repaired connection to heater and reassembled unit. Tested and checks good.

Replaced part listed ck okay

Installed new defrost heater in unit all checks good at this time.

Checked unit ops found unit to be leaking from tweaked tub advised customer about issues customer to buy a new unit.

Installed ice maker all opsmok

I replaced the broken suspension and gearcase with new parts and tested the unit out in diagnostics and normal cycles. All ops and components tested good. No leaks or excessive tapping or banging. Job complete.

Replaced ui control job complete

Installed new heater assembly due to bad connection on heater plug

Found bad ui and error for lost communication between main control and ui customer to replace unit.

Found bad wash basket and rods customer to replaced unit.

"I removed and replaced the heater, control, and air tower. All functions now check OK. Job complete."

Replaced refrigerator evaporator and heat exchange vacuumed and recharged job complete

Got to this unit to hear a rattling coming from the right hand bottom front. Remove the front of the unit to find that there were some Lego pieces sitting in the exit for the lint catch. I was able to remove these pieces and re-test unit. No further issues found at this time unit no longer making this vibration noise. asked customer to please have vents cleaned sense in discussion found that they had not had them clean in a good number of years.

"Install new drain pump, main control, and doorlatch tested operation of the unit and it is not working properly. Job complete.

"Complaint no cool in freezer. I found that there was a frost block surrounding the defrost thermistor. The thermistor read open. The fan, the heater and the harness all checked good. I replaced the thermistor with new part. Customers will advise if unit keeps acting up.

Complaint unit wont operate. I found that the unit was matted with lint. I also found that the heater coils were burnt apart and that the fuse was blown. I quoted the customers $375.21 for job and told customers I could fix them on the spot but they wanted to get a new unit.

Installed control and transformer. All checks okay.

Could not replicate noise at time of service cust will take recording of noise if issue happens again

Installed filter housing tested checked ok

Tech replaced doors . Tested unit all checks good

Install new DSI board. Ran short test and confirmed all ops functioning properly. Job complete.

Installed new main control. Tested operation of the internal and hood light. Unit is now working properly. Job complete.

Inspected unit and determine the flames on the front right burner or not generating enough pressure. Fix the problem by cleaning out the orfice and getting rid of the debris inside the office. The burner now is framing properly. Job complete

"Install new compressor, process valve and dryer. Vacuum system for 25 minutes. Recharge system with correct amount of refrigerant. 56grams of R600a. Unit is now cooling properly. Job complete.

Replaced controls job complete. Unit is working properly

Came to inspected unit and determine the bracket that allows the venting to go off to the pipe was never installed in the microwave. Looks like the installers got rid of it. Customer understood and will get that fixed. He is satisfied because now he knows what the problem is. Job complete.

"Replaced main control board, compressor and fans immediately kicked on and unit is cooling. Also sold customer a new filter. Everything checks OK at this time, advised Mrs to allow 24 hours to get down to temp before loading unit completely.

"Replaced cooling fan, did not need air switch. Tested unit and all checks OK at this time."

replaced evap. fan motor and checks ok

Changed the water valve. Tested component successfully. Unit operates as designed.

replaced bellow seal and checks ok

"Found burnt solder join on start relay. I soldered it multiple times and it just kept blowing out as if the relay was fried. Could not get relay to free up, cannot repair unit.

Replaced I/m ck cycle and fill ok

Installed control and drain pump and confirmed proper opperations ... unit is now working as it should

Installed control all ops ok.

"Refrigerator had sheet of ice on bottom freezer due to leaking from clogged drain line,I cleared all ice and drain line.

Go to the unit to find a streak of surface rust down the back of the unit on the left-hand side. This is typically been an indication that the inlet valve thermistor has failed and leaking to the outside of the unit. Was able to verify this by opening the top. Definitely in lit valve issue. Gave customer estimate and was approved for a new inlet valve. Installed new valve and ran diagnostics and checks. No further issues found at this time collected for part labor and service call today. Job complete.

Installed new bake element. Tested operation of the oven and it is now heating properly. Job complete.

"Rebuilt dishwasher with a new tub. Replaced the railings, the detergent dispenser, and the bottom rack. Unit tested successfully and operates as designed.

Installed new control board and entered unit into self diagnostics. Confirmed heating element working properly. Job complete.

"Oven settings wrong,I adjusted so oven will work on the settings control,I showed customer

"Got to the unit to find icemaker, not responding and diagnostics testing. Discussed with the customer that none of the tests were working at all. Discussed price of new icemaker with them and further testing. Was approved for icemaker changed icemaker out and was able to get harvest completed and send water to the maker. Unit should be able to produce ice at this time had performed a power reset as well. Job complete.

Got to the unit and installed new parts. Tested unit to find that the maker is now moving through harvest. Was able to send water to the maker. And had no issues with this installation at all. Control board is to ensure that this unit is going to work out of diagnostics on its own. No further issues seen it this time job complete.

Got to refrigerator ice bin was full of ice ref section was running at 37 degrees freezer section was at -1 degrees hooked gauges up unit running at +5 at the charging valve unit still has a full charge back cover was off the refrigerator installed back cover and explained to customer to monitor the temps when they see 40 degrees inside the fresh food section to call in for us to come out and check for dye

I replaced the main control. Unit is now sending power to the bake. All ops and components tested good. Unit heated up to temp. Job complete

"Tech replaced parts below to fix unit due to loud grinding noise . Tested unit all checks good

Dryer has a bad timer part is discontinued cust is going to buy a new dryer

"Found latch was improperly positioned in the door from the factory, causing it to not sit straight and control to not recognize door being shut. Repositioned latch assembly, ran through a cycle and all checks OK."

"Found bail arm down, popped arm up and also sold customer a new filter. All operations test OK at this time.

Found unit has full bin of ice tested temps all check ok tested fill al pass customer not happy with unit.

I replaced the pump assembly with new part. Ran unit in diagnostics and normal cycles. I could not find any leaks or errors with the unit. All ops and components tested good. Job complete

"Installed compressor, all checks okay.

Installed inner panel and leak went away. All ops ok

Installed new control but customer is still concerned about a noise in agitate i installed new slider but may have to replace transmission if customer calls back as it only makes the noise when unit is under a heavy load but i coud not get unit to make the noise

Installed new magnetron and put unit back together and installed it and confirmed quiet opperations with no loud vibrating noises like before

No one was home but I dropped it off next to their front door. Took a picture of where it was dropped off. Job complete.

Removed kickplate area and freed up stuck drawer rails and lubricated them. Job complete

"Found bad shifter causing cam not to disengage removed and replaced shifter and cam all ops and sounds tests normal customer to advise.

Reference# 1008470858 . Entered unit into diagnostics and found storage fault. Code F66. Performed auto test and confirmed. All office functioning properly. Call tech-support for further evaluation. Was advised only issue with unit is unit detecting slow airflow through filter. Advise consumer to wash filter every 2 to 3 dry cycles. Unit working as designed. Job complete.

"Installed new defrost heater assembly. Tested operation of the unit and it is now cooling properly. Job complete.

Installed new refrigerator door and freezer door due to rusted Ians pitted factory defective issue

Installed new harness assembly down by compressor and replaced water inlet valve up in the refrigerator ice room. Enter diagnostics and performed manual. Icemaker fill test. Confirmed no leaking water during icemaker fill or dispensing water through the door. Job complete.

Installed new chute and ice maker and valve and also found a kinked hose while replacing the hose so that may have been causing issues but let customer know if he has any issues call us in 30 days

Replaced control board and ui job complete

no fault codes in memory and fresh food section is cooling and working fine

Checked unit ops found icemaker to be dead not responding installed new icemaker tested unit completed a harvest cycle everything checks good at this time.

"Upon arrival found unit working Mr. paid house, told Mr if he has any problems in the future just call us back within 30 days"

Icemaker was turned off when I got here. Turned Icemaker on and Icemaker cycled and filled with water. Job complete

"Thermistor and damper reading open. Nto parts. Customer states would rather purchase a new freezer instead.

Installed new suspension rods tested unit in a cycle unit completed cycle with no issues everything checks good at this time

Installed new harness assy ref was in garage customer never came to door just opened garage did notice crack in bottom of freezer liner and freezer door hitting when closing center divider was bent out

"Found no motor operation, will not wash or spin. Found no power from CCU to MCU. Would need to return with both controls, replace CCU first and test the unit further to see if MCU is needed. Customer has opted to replace the unit due to cost of repair.

"fresh food drain clogged up , cleaned drain out and checks ok"

"Found Icemaker working as intended. Customer was not sure about how the arm was to operate so I explained it to him that if the arm hits ice it thinks the bucket is full. Also replaced filter for them and bled out water out of water filter, all ops ok."

I replaced the heater and Icemaker. All ops and components tested good. Customers will advise if the continue to have no ice.

"Pulled unit and removed junction box, turned power on and had no voltage from house supply into oven. Customer to contact electrician and will advise."

Replaced Icemaker thermistor error