Found many fault codes but one to get unit back to working order would need to be ordered and customer declined further repairs as they do not want to wait for order parts and they have company coming

"Installed new dryer belt customer.

"Installed new drain pump due to not running or draining,f8e4 error code save,tested good afterwards.

"Dryer lint shroud clogged up with socks and lint,blower wheel caked with lint ,I cleared out but recommended vent cleaning service come now.

Installed rods all ops ok.

Replaced broken harness and confirmed unit working properly at this time.

"Customer concerned that the unit will not turn on. Confirmed issue. Upon arrival, found proper power and polarity at the outlet. Was able to get unit into diagnostics and found lid lock fault. Checked lid lock and found latch not operating properly. Installed new lid lock from stock, tested and calibrated unit, all ops good. Job complete.

"Cx complaint: water/ ice on the floor of the crisper drawers leaking onto kitchen floor.Upon arrival, confirmed cx complaint, found a sheet of ice on the floor of the crisper drawers leaking onto section.Entered diagnostics, all thermistors and fans checked okay. Called techline and spoke with Adrian. Techline suspects a clogged defrost drain. Pulled the unit out and fished a brush up the defrost drain to remove any debris. Advised cx to call the office if issues persist.

"Per the customer, reported noise issue only occurs through the first few minutes of initiating cooling operations. Unit turned off for est 10min before resuming cooling operations. All start up procedures initiated without fault and/or abnormal sound issues. Unable to duplicate reported issue. Based on customers description, reported sound issue may be that of normal operation caused by flow of refrigerant leading to thermal expansion and contraction of materials resulting in reported sounds till temperatures and system pressures stabilize. If the case, repair service is not required. As the unit is otherwise operating at temperature without fault and/or additional sound issues, sealed system service would not be recommended as an attempt to resolve issue. Customer instructed to monitor and if possible record sound issue when occurring and advise should further service be required.

"door latch screws were loose and switch not closing to turn lights off , fixed screws and checks ok"

replaed both light switches and unit is now working as it should. Job complete.

Found unit with worn belt slipping off pulley. Replaced belt all checks ok

"Replaced reservoir, valve, fill tube and heater. All checks ok

Installed new ice bin door. Confirmed ice bin filled up completely with ice cubes. Job complete.

"Customer concerned that the unit is still not making ice. Confirmed issue. Upon arrival, checked temperature in the freezer and its good. Ran through all tests in diagnostics and all are passing. However, noticed same error code displaying from the last visit and the ice bin light is not on. Reset unit at the breaker and ran ice maker test again and the error code went away. Ice bin sensor is lit up now. Informed customer to give the unit until tomorrow to produce ice. If the customer doesnt have ice by tomorrow morning, we will need to pre order a few parts. Job complete.

"Applied sealant to mullion cover and installed new door. All checks ok, customer to advise

"Found unit shaking when ramping up into high speed spin due to badly worn shock absorbers. All other components check OK and no other fault codes present in unit. Replaced all 4 shock absorbers, ran through a quick wash and all operations test OK at this time."

"On arrival found the unit disconnected from power and filled with est. 8' inches of standing water. Unit restored to power after which the units drain pump was energized and drained all water within 8min. Heavy black residue exists coating and staining the ice bin from the prior water level down. Will not be possible to fully restore to a true white condition. With all water drained found multiple white plastic pieces at the ice bin floor, through inspection found to be remnants of the ice sweep. Unit initiated ice production. Found minor to moderate squealing originating from the units ice mill, prelude to failure. No less than a new ice sweep, retainer screw and deep clean of both the ice bin and drain pressure system will be needed to correct. Ice mill assembly will likely need replacement shortly there after, if not immediately. As the unit has passed all manufacture warranty, not purchased by the current homeowner and does not fit the current homeowner's ideal needs, the customer has opted not to advance with repair service but to replace upon returning to the home next season. Customer will call to inquire on available replacement options on or prior to returning to the home.

"Found control throwing dr code when attempting to run bake or broil cycles. When unit is entered into service diagnostics the control is flashing F13 internal control failure. Dr code is most likely a glitch and side effect of the control failure as this code usually means door switch problem but the door switch checks OK. Advised customer would need to replace ACU and Overlay to repair. When part number is pulled up, the ACU shows some inventory available but is reading as discontinued from WCI. Parts may be getting ready to become obsolete for this unit. Customer will call and advise the office if they would like parts ordered."

"Found failed wash motor and heater, gave cust estimate. Not worth repair"

"Installed valve, all ops ok.

Removed and replaced part all ops test ok

Installed all new parts. Tested operation of the unit and it is now working properly and making its normal operational noises. Job complete.

Installed new control and confirmed unit working properly

Replaced actuator and cam they were both not functioning

Got to this unit to find that the icemaker indeed was not responding. Powered on and off and still no response from icemaker. Gave customer estimate for new icemaker and labor. Customer approved. Was able to install new icemaker and run through harvest cycle. New icemaker responded correctly and should be making ice. Ask customer to please let us know if this unit does not complete making a full bit of ice within 24 to 48 hours.Job complete.

Found ice maker motor stripped out as i was using jump wire to cycle unit and it was failing.. Confirmed water going in during cycle and advised customer to give unit time and bin may take up to 3 days to fill bin

Installed new right trim and was able to get unit back to looking and working standards

Installed all new parts. Tested operation of the unit and it is now working properly. Job complete.

"Installed new control board and recalibrated unit, tested operation, unit is running properly at this time."

"Checked unit over for safety. There is nothing mechanically wrong with this unit, no physical damage to unit itself, customer states was steaming vegetables and the turntable broke. Whirlpool is sending her a new turntable free of charge. Unit is mechanically sound."

Installed new user interface and paddles and advised customer to continue monitoring for resetting problem. Have not been able to see it in that state during appointments.

Found unit filling with the proper amount of water all ops thats OK no stored error codes call Tech line ran through test advised all operations are normal. SR number 7741128428.

Installed all ordered parts and confirmed unit working properly and quietly at this time

Found an adjusted icemaker confirmed unit working properly

Installed new actuator. Performed DLMS calibration. Performed auto test in diagnostics. Started a normal wash cycle. Confirmed all ops functioning properly now. Job complete.

Installed new repair kit. Tested operation of the unit and it is now working properly and making its normal operational noises. Job complete.

"Found failed ice maker, installed ice maker, all checks okay.

"Installed control, all checks okay."

"New evaporator fan motor assembly with harness installed. All initial units test and operations check good upon completion of service. Customer to monitor unit temperatures, operations, sounds, etc. and advise should further service be required.

"Found the units ice bin filled to 1/4 capacity with solid and full sized ice cubes. Confirmed all eight segments of the ice maker cube mold filled with solid ice. Ice maker initiated harvest cycle. Loud clicking could be heard from the ice maker module, harvest stripper stalling through rotation. New ice maker supplied by pre-ID installed to correct. New ice maker initiated and completed harvest cycle to include proper water fill without fault, water leaks and/or abnormal sounds. All unit operations check good upon completion of service. Customer to monitor units ice production and advise should further service be required."

Found unit had a weak thermal cutoff. Replaced part all ops ok.

Installed control and latch all ops ok.

Replaced bottom drawer slides job completw

Checked unit l it was working ok while I was there. Cust will get a video of it not working the next time it does what they are saying

Got this unit and was able to install new user interface. Also sealed the gap between the dispenser and the user interface so that this unit would stop dripping out the front. Ran testing to find that these parts are indeed now working and found no further water leaks after resolution.Job complete.

"Cx complaint: dishwasher leakingUpon arrival, started a normal cycle and confirmed cx complaint. Found unit leaking from the Sump&motor assembly. Quoted cx for a new sump&motor and received confirmation for the repair. Replaced Sump&motor with pre IDd part. Tested operations successfully with no leaks. Unit operates as designed.

Installed new door. Set time and date. Ran short test and confirmed all ops functioning properly. Job complete.

"Found rear seal on drum had flipped, causing an air gap, preventing proper airflow through drum. Issue was causing gas valve to prematurely cycle off. Re-seated felt seal to proper position and confirmed unit has excellent exhaust flow now. Confirmed flame stays on 10 times longer now. Job complete."

"Installed new part, tested unit, all ops good. Job complete."

Inspected unit and determine the evap fan motor bracket was faulty loose so every time the Evap fan motor runs it would rattle and make loud noises. Repaired problem by reinstalling the bracket tightly and securely. The evap fan motor is now running smoothly. Tested properly. Job complete.

"New electronic control, main wire harness, RH cooktop harness and RF dual infinite switch installed. Multimeter testing conducted prior to restoring power confirming no resistance from L1 / L2 to Neutral / Ground. Power restored for testing. Confirmed full unit operations restored. All unit tests and operations check good upon completion of service. Customer to continue normal use of the unit and advise should further service be required. Original control marked and retained for core return.

"New door hinges and hinge receivers installed restoring proper door function and seal. All unit operations check good upon completion of service. Customer to continue normal use of the unit, monitor and advise should further service be required.

"New electronic control installed. Unit ran through calibration cycle, diagnostic auto test and initial Rinse, Drain & Spin cycle without fault and/or water leaks. All unit operations check good upon completion of service. Customer to continue normal use of the unit and advise should further service be required. Original faulty control marked and retained for core return."

"Installed parts, all checks okay."

Replaced defective lid lock assembly. Ran an auto test to completion successfully. Unit now operates as designed.

"Cx complaint: unit wont run a cycle.*Upon arrival, entered diagnostics found an f3e1 EC for a pressure system fault. Removed the top to inspect the main control, found pressure hose off of the main board. Found no obstructions in the pressure hose, and reinstalled. Cleared the error code and ran an auto test successfully. Unit operates as designed."

"Cx complaint: unit wont run a cycle.Upon arrival, entered diagnostics found F4E3 for a bad Sump&motor assembly. Replaced with pre IDd part. Tested operations successfully with no leaks. Unit operates as designed."

Replaced main control board. Completed function test. All checks ok

"Installed both parts, found main control blew due to a fault with the outlet. Advised cust to call electrician and repair outlet."

"Inspected Unit and determine the unit was not leveled. Therefore the doors would not seal as tightly. Repair problem by lowering the feet on the refrigerator, which then raised the front and leveled the unit. The door doors are now sealing properly. Also reinstalled the door handle tightly for customer. Job complete.

Checked unit. Adjusted door and removed ice build up. Job complete

"Installed handle, all checks okay."

"Installed frz evaporator fan motor, all checks okay. Freezer should go down to temperature, so it will make ice and the fridge should also even out."

"Installed whirlpool supplied evaporator, vacuumed and charged, all checks okay at this time."

"Stove right real small burner coil open,installed new rr rear burner and tested,working good now

Removed and replaced all LEDs all ops tested OK customer to advise

"Checked for issue dispensing. Found dispenser defective, replaced dispenser and tested operation, unit is running properly at this time."

"Installed new evaporator fan, cleared drain line and reprogrammed fridge. Unit running properly at this time."

"Checked for frosting in freezer, found gasket pinched at top right side of freezer. Applied heat source and shaped gasket to match unit, unit running properly at this time.

Replaced Evap fan and switch. All checks ok

Replaced IM. All checks ok

Go back to this unit and was able to install the parts that were ordered. Tested operation of this unit after installation of the parts and found oven to be working correctly. Also tested burners and insured function of those. No further issues appear to be present at this time. Job complete.

Installed new control and actuator confirmed unit working properly at this time.

Installed parts tested checked ok

"Installed new vent, and bezel. Installed new lower door seal. Perform multiple test and could not find any water leaking. Advised Mr., if issue returns, to make a recording with phone of whats going on with unit. Job complete.

"Found unit was unplugged upon arrival. After plugging unit back in, confirmed drain pump continuously running. Placed unit into diagnostic mode and found stored fault code F3E1 (failed pressure sensor in control) installed new control. Performed calibration and auto test. Confirmed all ops functioning properly. Job complete."

"Installed new parts, tested unit, all ops good. Job complete."

Inspected unit and determine all components chcked out good. Had to give customer some advise / suggestions on how to use the washer to its best capabilities. He understood. Job complete.

Inspected unit and determine the hot wire connection going from the main board to the cold water solenoid was faulty loose therefore not activating the valve. So cycles were not receiving water into the tub. Repaired problem by reinstalling the wire connection tightly and securely to the valve. Cold solenoid is now working properly . Job complete.

replaced mullion and checks ok

"Installed new control board and tested operation, unit is running properly at this time."

All ops test ok instructed customer on ops and care customer to advise.

Found bad lower harness removed and replaced parts listed all all ops test ok

"Found burner staying on high. Replaced infinite switch. All checks ok

SR7741110370 After speaking with techline and testing unit we found the vent will need to be replaced testing with the meter after wew found the F10E2 code and than a F9E2 which while testing from drain board ... Is recommended to replace drain pump aslo... Customers knows they have 30 days to decide if they want the parts ordered

"Installed new control panel due to f2e0 error and not able to set selections,tested good afterwards"

Inspected unit and determine the fill tube water line going to the ice maker was frozen therefore now filling up the icemaker to make ice. Ran a test on the icemaker and water valve and they both check out good. Defrosted the fill tube line and it is now working properly. Job complete.

"Rather than pay additional labor charges to modify the FC liner for installation of a new updated multipoint LED module, the customer has opted to omit the second updated LED module. Exposed wire harnesses for the second LED module connected with a Wego type electrical connector in order to complete the LED circuit. All remaining single point LED modules uninstalled and replaced with the updated multipoint LED modules. Power restored confirming full interior illumination restored with exception to the second FC LED module. Total due adjusted to reflect actual labor time required to complete repair.

Found unit lost calibration ran calibration cycle all ops past customer to advise

"Installed gear case and gear case components with a new basket and washplate... Unit is now back to working like it should and customer is happy

Installed new control and tested unit and it worked how it is supposed to and customer is happy

"Installed new icemaker and tested,unit cycled and filled

"Refrigerator has reverse osmosis hooked up to the supply line,the icemaker fill tube was frozen up after plumbers changed the system bladder,I cleared fill tube with my steamer and tested fill,the unit only filled about half in 7seconds fill time,need bypass but its discontinued

Removed and replaced panel all ops tested OK customer to advise

"Installed parts, all checks okay."

"Go to this unit to find that the suspension was indeed bad. Further testing also found that the actuator was no good and not shifting correctly. Was able to change these parts and get the unit back to a normal working situation. Ran calibration after these parts were changed as well as automatic test. No further issues found. Job complete.

Removed and replaced parts listed all ops test OK customer to advise

Installed new control confirmed unit working properly at this time

Inspected unit and determine customer was loading cloths correctly therefore the cycle would not balance the clothes and would time out without spinning. Advised customer if it happens again she needs to add a few more fabric into cycle. She understood. Job complete.