Removed and replaced parts listed all ops test ok customer to advise.

Replaced dispenser assy. Checked ok job complete

repaired burnt wire to heater and checks ok

Unit is gonna be replaced due to safety issue that occurred . Did make adjustment to burner and overclocked it to reduce time reaction .

Installed tested checked ok

Got back to the unit and was able to install new basket. After basket installation tested operation of unit and unit is now working correctly. No further issues found at this time job complete.

Installed new icemaker and confirmed unit working properly

"New upper oven appliance manager (Covered under a manufacture 5yr Part Only Warranty), vent tube and cover installed. Vent cover assembly fully sealed with high temp silver tape as per Wpl T/L instruct in attempt to prevent reoccurring failure, pictures attached for reference. All initial unit tests and operations check good upon completion of service. Customer to continue normal use of the unit and advise should further service be required.

I removed and replaced the freezer evaporator harness assembly and also freezer evaporator fan. All functions now check OK. Job complete.

"Found evaporator iced over upon arrival, found evaporator thermometer thanks temp is at 60? when iced over. Installed new thermometer onto evaporator and advise customer only charging for part. Job complete.

"Replaced user interface assembly. Calibrated and tested unit, adjusted leveling feet and all operations test OK at this time."

"Install new compressor and recharge with 68 g of R 600 a confirmed good heat transfer. Advise Mr. to monitor unit calls back if he has any issues.

Installed new RC evap fan motor with sensor and drain pan kit. Tested operation of the unit and it is now working properly. Job complete.

Installed new main control. Tested operation of the unit and it is now working properly. Job complete.

Install new RC evaporator fan motor with sensor. Tested operation of the unit and it is now cooling properly. Job complete.

replaced compressor and checks ok

"Installed all new parts, tested unit, all ops good. Job complete.

"Installed new suspension in washer bouncing around,tested good after calibration

"Recall - tripping breaker, dryer is on a double 20 amp breaker needs to be on 30 I explained to the customer"

New door switch installed restoring full and continuous operation through cycles. All unit operations check good upon completion of service. Customer to advise.

"Confirmed manufacture defect of the original FC door, wide spread rust with pitting. New FC door installed. Unit ran through full diagnostic testing, ice maker harvest cycle test and dispenser functions test all without fault and/or water leaks. All unit test, operations and cosmetic appearance check good upon completion of service. Customer to advise."

"Removed and replaced parts listed all ops test ok customer to advise.

Removed and replaced parts listed all ops test ok customer to advise no charge for switch and bezels

Installed parts tested checked ok

"New HMI panel installed. Unit ran through full diagnostic testing and initial Rinse, Drain & Spin cycle without fault and/or water leaks. All unit tests and operations check good upon completion of service. Customer to advise.

"Installed Dishrack, all checks okay."

Removed and replaced part all ops test ok customer to advise.

Went to install drain pump and found something obstucted it and water started pouring out as trying to shop vac from the back hose was not working... But i was ready and was able to catch all water coming out... Installed new drain pump and encoder and new control and confirmed unit went through all testing... Advised customer to run affresh before running clothes through washer and advised customer if anything happens in the next 30 days to give us call

Diagnosed unit and determine the broil in the oven is working properly. It is heating at the right temperature. Advised customer and he understood. Job complete.

Inspected unit and determine the right door hinge was faulty loose therefore not allowing the door to close all the way. Repaired problem by reinstalling the door hinge tightly and securely. Door is now sealing and closing properly. Also leveled unit for customer. Job complete.

Came to inspect unit and determine the temperature in the freezer was not up to par ..took the freezer cover off and notice too much ice buildup on the evap sensor which could be throwing it off. Defrosted the whole evap coil completely and also tightened the sensor to the coil. Advise customer to give it about 3 days and she should see a difference in temperature. Unit is now working properly. Job complete.

"Installed parts, all checks okay.

"Found the unit had been disconnected from power prior to service. Power restored for testing, units drive motor immediately energized rotating the drum, no cycling of the heater circuit. Units UI responsive, audible tone when selecting any key function, however, unable to cancel and/or change displayed 151 fault. Only the units power button functioning normally. Confirmed failure due to a faulty main control, double line break shorted closed. New main control supplied by pre-ID installed to correct. Operational testing conducted confirming full unit operation has been restored. Customer to continue normal use of the unit and advise should further service be required.

"replaced freezer compressor and cond. fan motor , unit started cooling fine

"Installed new diffuser due to noisey operation,tested good afterwards"

1027#gc go to this unit and found the compressor kicking on and off. This is a clear sign that the start run device is failing or has failed. Because of this gave customer estimate for the part to be replaced. After estimate was approved installed new part and tested.unit appears to be working correctly and no further issues at this time job complete.

"New left side RC door gasket installed. Both previously installed right side RC door gasket and new left side RC door gasket heated to reform ensuring proper seal and lubricated along the outer edges to help prevent rolling. All unit tests and operations to include proper seal check good upon completion of service.

"Installed new control panel and light switch due to lights out and control not working,tested good afterwards.

replaced fresh food thermister and customer to advise on cooling in fresh food section

"Removed and replaced parts listed all ops test ok

Found defective evaporator fan. Fan motor is getting 120vac but not cycling. Installed new evaporator fan and thawed out the water tank since it was frozen due to fan not running. All ops good. Job complete.

"Installed microwave and tested, all ops good. Job complete."

Installed new console and tried to hook up wifi for customer but unit would not connect.... called connect team and they are trying to push unit through but have told the customer to scan the QR code in 24hrs and follow the steps through the app... We did confirm unit heating and shutting off as it should

"Installed new shelf glass and reinstalled all shelves that were removed,tested good afterwards.

Installed insulation around evaporator inlet tubing. Confirmed quieter operation. Job complete.

"Found auger motor locked up while trying to dispense ice. Was able to unseized the motor and now is dispensing ice properly. Advised, if issue returns in the near future, auger motor will need to be replaced. Also, found freezer drain hole clogged with ice again. Contacted tech-support and was advised to attach solid wire to defrost heater and place in hole to prevent freeze over. Made repair and advised Mrs. to monitor refrigerator."

Installed new dampers and perform short test. Confirms unit properly spends without bouncing around now. Job complete.

"Installed new part, tested and calibrated, all ops good.

Got to this unit and was able to fix it with the parts that were ordered. Tested operation of the unit to find all parts working correctly now. Job complete.

Go to this unit and replaced pump with new. Use the miscellaneous parts to ensure this unit was installed correctly. Unit working correctly no further issues found at this time. Job complete.

"Installed new sensor bar and sensor due to not sensor drying,getting f3e5,tested good afterwards

I removed and replaced the ordered parts. All functions now check ok.Job complete

Checked unit found sealed system issue. Cooling but not cold enough. The control display is bad and cannot go into diagnostics. Unit is not cost effective to repair everything needed. Cust going to get a new unit. Job complete

Replaced control on lower oven. Job complete

"Replaced compressor. Tested system. All checks ok

Found unit has worn cam replaced part listed ck operation ok

"Spoke to Steve at tech line sr#7739533844. Case file 7739497258. Installed new hinge and found damage to frame where it was hot by something and bent the frame in which causes the door to bind up and not seal favtory or installers tried to cover it up by putting a piece of metal behind hinge to bring the door out but caused a significant gap. Spoke to tech line and trade partners, unit is deemed unrepairable.

Replaced harness and completed function test. All checks ok

"Unit located in the homes garage, connected to a GFCI circuit, no power. Customer had located and reset the tripped GFCI outlet. With power restored all start up procedures initiated without fault. Customer to monitor unit operations and temperature and advise should further service be required.

"On arrival testing conducted confirming prior diagnosed upper cooling fan motor failure. New upper cooling fan motor installed. Testing again conducted confirming full unit operation has been restored. Customer to advise.

"Found freezer frozen over, drain clogged and fan hitting ice. Door was not shutting well. Defrosted drain and cleared ice out, door is now shutting better however I advised customer that freezer rails are missing ball bearings and rails are NLA. Also ice production stopped which was most likely due to temp issues, but also found filter seized in housing, which may need to be replaced. If ice production does not resume customer will advise if they would like housing and filter ordered. All checks OK at this time. Customer will monitor and advise.

Installed new control and console and confirmed no leaks during testing and advised customer to monitor unit and call us back within 30 days if there is any issues

New ice maker assembly installed. All initial unit tests and operations check good upon completion of service. Customer to monitor and advise should further service be required.

Installed new board and automactically it communicated with main board and had the right amount of filter status... Explained to customer service call is good for 30 days and part is good for a year

Replaced both door switches and door gasket.

Replaced ui control job complete

Installed new wash pump assembly due to bad motor. Tested good after work.

"Found fill tube frozen over, cleared tube and cycled Icemaker all ops ok."

Installed parts. All checks okay

Installed tines. All checks okay.

"Dryer noisey due to bad support rollers,belt and idler pulley,installed new support rollers,belt and pulley,tested good afterwards,

Removed and replaced maker assy and valve all ops test ok customer to advise.

Installed new AC you and confirm unit working properly now. Job complete.

"Installed clip on bottom drawer stabilizer bar,tested good afterwards"

Installed tested checked ok

"Removed and replaced maker assy cleared drain line all ops test ok customer to advise.

"Installed part, all checks okay.

Installed and freezer fan and UI advised Mrs. to monitor

"Installed new ice bucket and dual fill valve due to leaking and freezing in bucket causing to break,tested good afterwards.

Installed new auger assembly perform short test and confirmed ice dispensing properly now. Job complete.

"Installed new compressor, process valve and drier. Vacuumed system for 30min. Recharged system with correct amount of refrigerant 53gram R600a. Unit is now cooling properly. Job complete.

"Got to this unit to find that we had multiple lights not working in both sections. Freezer light definitely out on look over. Also seeing multiple other lights in the refrigerator section having difficulty being lit. Service pointer applies to this unit and makes it to where service call is the only thing being collected for today.parts and labor are covered as it says in service pointer. After installation of all lights, insured function all lights. No further issues seen at this time. Job complete."

New electronic control installed. Unit ran through full diagnostic testing without fault. All unit operations check good upon completion of service. Customer to advise. Original control marked and retained for core return.

Replaced lower door seal. Job complete

Got to this unit and was able to remove old wash pump and install new. After installation tested the unit through automatic cycle. Unit ran through entire cycle without issue and is pumping and washing. Unit drained out as well as heat cycle at the end. No further issues found at this time. Job complete.

"Got to this unit and found freezer temperatures to be good for making ice as far as I can tell. Ice cream in the freezer section was nice and firm. Unit had ice in the icemaker, but it was not kicking it out. Did find error code E5 on this unit which typically is an issue for the icemaker specifically but has led to computer board issues. There have been occasions where the icemaker gets replaced and does not do the job whereas the control board has the ability to fix this. express this to the customer and gave estimate for part on that if that were to be the situation. Did a power reset on this unit and found all parts appear to be working correctly. Unit was able to be delivered water. At this time, we will have to wait to find out if the icemaker will work on its own accord. If it does not, it is my opinion that the control board needs to be replaced and the customer is aware of this information. spoke with Dale on this unit to see if service call was necessary for todays appointment. As we discussed no service call is to be charged at this time. Customer to let us know if unit is not producing ice within 24 to 48 hour.

Replaced side panels on the dryer. Job complete

Steamed out frzr and replaced pcb and thermistor. All checks ok

Installed parts ch3cked ok

Installed timer customer provided ck ok

Install new lower icemaker. Tested operation of the unit and it is not receiving water. Working properly. Job complete.

"Found bad maker power to unit will not cycle removed and replaced maker all ops test ok customer to-advise.

No model/serial sticker. Instructed customer to return to store.

Unit has been working fine since Mrs called. Unit had a full frost pattern and temps check OK. Mrs will advise on unit.

Started cleaning cycle using customer supplied cleaner. All checks OK.

Found unit not cooling and temp over 80F. Put into diagnostics and found faults for F0111 Freezer Air NTC and F0122 Ambient Air NTC. Per Miele this can happen with a no-cool situation. Compressor was clicking off on overload. Opened overload and found burnt contacts. Replaced overload from miscellaneous truck stock. Compressor immediately fired up and fans were running. Mrs will monitor and advise on unit.

Installed new door ice and advised customer to monitor unit and if any issues in the next 30 days to call us

Got back to this unit and hooked up the smart device to the refrigerator to find out it did need a update to the software. With the customers approval ran the update to the software. After software update went through testing and found that the evaporator fan and the refrigerator section still was not working. Tried to operate through testing it would not. Replace the evaporator fan in the refrigerator section and tested. fan now working correctly. Reset the unit power and confirmed operation. No further issues found at this time. Collected for heart labor and update for the software. Job complete.

"Washer lid spring came off due to holder loosening up,I tightened again and tested good afterwards.

"Found f8e4 code indicating float switch failure, tested unit and confirmed unit working properly advise Mrs. to monitor.