"Installed new icemaker due to leaking one,tested good afterwards

Replaced drum rear seal and belt job complete

Removed and replaced parts listed all ops test ok

Unit has a noisy rear bearing and worn out dampers and cust wants bellow to be replaced this is not worth all those repairs. Cust getting new unit

"Installed new ui control and main control due to erratic temps,when I arrived the freezer was in minus - temps refrigerator or ff section perfect 38* per setting versus the last time ice melting and warm temps in top"

Installed new pump & motor. Tested operation of the unit and it is now working properly. Job complete.

Installed foam gasket on freezer door behind door gasket.

Replaced sump assy. Completed function test. All checks ok

"Customer reported FF section temperatures were climbing yesterday, upwards of 50F and unit was beeping and flashing a wrench. On arrival today both sections matched set point, around 0F and 37F. No wrenches were in the display and using service diagnostics, no fault codes were stored in the controls. Auto test did not indicate any problems. Both compressors are operational, both evaporator fan motors and condenser fan motor running strong. I did clean the condenser today as it was due for cleaning, however, most likely that would not have caused one section to stop cooling. Advised customer to keep an eye on the unit and call for service if issue returns. All checks OK at time of service."

Found compressor running for about 10-15 seconds and clicking off on overload. Replaced relay/overload combo and compressor is now on and running. Opened up overload and verified burnt contacts. Unit is cooling and all checks OK.

"Install new spark, modular board, igniter, and bake burner. Tested operation of the oven and it is now baking and heating properly. Job complete.

Inspected unit and determine the wire connection going from the spark modular board to the broil igniter was faulty loose touching ground therefore tripping breaker. Repaired problem by reinstalling the wire connection tightly and securely to the broil element so its no longer loose. Unit is now working properly. Job complete.

Replaced wash motor assy. Checked operation ok job complete

Replaced lid catch checked operation ok job completed .841 STRIKE

"Found unit not starting due to bad thermal cutoff. Replaced cutoff with one from truck stock and completed function test. Major airflow blockage. Instructed customer to have vents cleaned. All checks ok aside from airflow.

I started by emptying the unit of water with my shop vac. As it would not drain on its own. I removed the drain pump and found that the impeller was frozen and would not turn. I spun it by hand and the impeller freed itself up. I then reinstalled drain pump And tested all functions and unit checks OK. Job complete.

Installed heater all ops ok.

Defrost terminator was bad replaced defrost terminator. Job complete

replaced lower door hinge and checks ok

Removed and replaced check valve and dispenser assembly. All operations test OK at this time.

"Installed parts, all checks okay.

"Installed control, customer to advise if noise returns."

Gained access to both evaporators. Opened switching valve at step 4 in diagnostics. Unplugged unit. Tapped into process stub. Found standing pressure at -25 in a vacuum. Pressurized system with 250# nitrogen. Unable to find any external leaks using bubble solution. Let unit sit for 30 minutes and system held pressure at 250#. Installed a dye drier and recharged system with 170g R134a. Advised to allow 24hrs before temps are back to normal.

"GATE/DOOR CODE: *40948. Customer concerned that the unit is not cooling properly and is not making ice. Confirmed issue. Upon arrival, checked temperature in the freezer and got 20 degrees. Partial frost on both evaporators and condenser is clean. All fans working. Noticed compressor sounds abnormal. Due to the weak frost pattern, temperatures, and noise of the compressor, we will need to replace the compressor and drier. Quoted customer to repair the unit. Entitlement page shows unit is over 10 years old so I am not able to get coverage on the sealed system. Customer declining repair at this time. Job complete."

"Customer concerned that the unit is not spinning properly. Checked through all components in diagnostics and all components check good. Tested suspension and found that the suspension is too bouncy. Need to install new suspension kit. Quoted customer for the repair. Customer approved repair cost. Installed new suspension and calibrated unit, tested, all ops good. Job complete."

New inlet water valve and pressure switch installed. Unit ran through operational testing now without fault and/or water leaks. All unit operations check good upon completion of service. Customer to advise.

Replaced upper and lower spray arms and insulation on toe kick. All checks ok

"Unit has failed pressure switch, unit would need control but not worth repair for cust.

Removed and replaced evaporator fan motor. New fan is blowing strong and all operations test OK at this time.

Replaced main control and fan/harness assembly. Unit is on and cooling and all operations test OK at this time.

Installed new pump and confirmed water filling and detected no leaks and confirmed unit now working like it should and customer is happy

Unit was working power cycle must have glitched the board its working fine now

Replaced control board. Unit is working ok job complete

"Upon arrival, found freezer at 40? and refrigerator at 43?. Confirmed compressor running but poor heat transfer from discharge line removed evaporator cover and found no frost pattern due to refrigerant leaked out. Estimate to hunt for leak and possibly repair Will be too costly.

"Install new magnetron, capacitor, diode transformer due to bad shorten system unit working good now

"Sr#7739796273 got to this unit to install new cooktop hinges, and one other screw to complete the framework of the cooktop upper. Had a little difficulty getting the cooktop off as this is slightly a new design and had difficulty getting to the rear secure. Was able to call tech line and get some assistance getting this unit apart and back together. Once done so tested to find that the front door is opening and closing, more like it should and more like it was designed. As well as cooktop in good position no longer having gaps where the glass was no longer adhesed to the cooktop. All parts are working correctly. Job complete."

"Got to this unit to find that the customer was stating that this unit was not filling up with water. Immediately started testing the unit and found no error codes. No error codes were found started to run an automatic test. Automatic test did not show any issues whatsoever. Because of this, had a decent conversation with the customer to make sure there was no other discrepancies with the way that they were operating the machine and discovered that the customer had a few issues with how they had been starting and stopping this unit. Was able to clarify a lot of this information for the customer and hopefully will no longer have problems from what I see here today.collected for service call only today. Job complete.; dspstn on spec-tagged invntry: 1 W11513255 VALVE"

"Freezer door gasket at the top has condensation,I heated gasket with hair dryer and added strip under in front per service pointer ,customer will monitor

"Installed new parts, tested unit and defrosted all ice, all ops good. Job complete.

"Installed new parts, tested unit, all ops good. Job complete."

"Installed new control and valve ordered for refrigerator not making ice,tested good after testing on test 96,then 97

Installed new dual water valve and icemaker. Tested operation of the icemaker and it is now receiving water working properly. Job complete.

Replaced control board. Completed function test. All checks ok

Removed and replaced ui all ops test ok at this time customer to advise.

Came to the house and realized the unit was never leveled so therefore the doors were not sealing all the way when you close them. Level the unit. Also on service test 34 I set the vertical million to be on at all times due to the fact that were here in Florida and theres a lot of humidity. Unit is not working properly. Customer understood and satisfied. Job complete.

I removed and replace the interlock kit. Job complete.

"Installed gearcase and basket, all checks okay."

"Installed new door lock switch assembly,tested good afterwards,.

"Installed new parts, also found defective actuator. Tested and calibrated, all ops good. Job complete.

"unit is leaking through the seals in wash motor assm. , parts have been discontinued for this unit it's 26 years old

"main control board is bad , just clicks and no power out to fans or compressor"

All ops test ok unit is 3/4 full of ice customer to advise.

Removed and Installed new ice machine. Tested for leaks and verified proper fill and drain. All checks OK.

Installed new pump new lower harness and control and confirmed unit working as it should and customer is happy

Installed new suspsenion rods and confirmed unit in a nice smooth spin

Installed new damper control and confirmed quiet operation. Job complete.

"Found unit with motor not starting due to failed capacitor. Replace capacitor with one from truck stock. Completed function test. All checks ok

Replaced upper and lower spray arms and insulation on toe kick. All checks ok

"Found wire loose reinstalled checked ok

Replaced LH and RH rails. Verified door is now closing properly and gasket is sealing all the way around. All checks OK at this time.

"replaced water valve , vent , and control and checks ok"

"Replaced Gearcase, hub, and wash plate. Completed function test. All checks ok

"Found insulation on back wall saturated. Back walls starting to sweat and form ice. cannot repair."

"Found excess lint build up in rollers and pulley, cleaned out lint all moving parts move freely. All ops ok."

Fc temp 1* ff temp 38*. Ice maker is making 4-5 batches a day. Explained to customer that it is normal operation. Unit working as designed

Found unit runs but does not heat. Mag is shorted to ground. Unit has no model and serial tag for proper part lookup and would not be economical to repair regardless. Customer to replace.

"Installed new tub due to leak,also replaced left top rack track bracket,tested good afterwards"

"Got back to this unit and was able to install new motor and shaft and other small parts associated with this. Found an determined that the motor that attached to the shaft had been rounded off, and the shaft had also been affected by this so indeed replaced all parts that were needed here. Put the unit back together and tested. Found the unit be able to distribute both crushed and cubed ice without issue. Job complete.

"Install new extension drain hose. Dishwasher is now draining and working properly. Job complete

"Confirmed cosmetic damage reported. Per customer request, new cooktop installed to correct. No fault error codes recorded in unit history. All unit operations and cooktop cosmetic finish check good upon completion of service. Customer to advise.

Installed new timer and tested unit to make sure it works. Timer is working properly.

SR7739786942 After trying water fill test as unit would only energized for a half a second we tried new one with no results so called techline and found you have to test 96 before 97 or unit will not work properly according to the software so put everything back together and put new icemaker in and filled fill cups and advised customer to monitor ice production

Installed heater and cleared line. Cycled ice maker and unit filled with water. All ops ok

"New crisper shelves, drawer pans and door bin installed restoring optimal drawer function. Customer to advise."

Got this unit and found that the water was having trouble coming into this unit. Finding full voltage going to the valve. Tested and found that the harness is in good condition. Only seeing issue with the Coldwater side of the valve. Was able to replace this part and test. No further issues found at this time. job complete

"Got back to this unit today and installed new ACU. After installation ran a quick cycle as to try to re-create the issue we were having. On previous cycles tested the unit could barely make it through with a lighter load of towels saying that it had a suds condition. These tests had no detergent added to them, nor was there any suds seen during the wash portion of the cycle. This was the reason for getting this computer and testing now. With this testing on the quick cycle, found that the unit was able to complete the cycle without issue. This one was somewhat out of balance to begin with so I believe this was a good test for this. Unit was able to complete the cycle as it had not previously. This was a great indication that the unit wants to move forward and should have no further issues known at this time. Ask customer to please start doing some laundry so that we could find this confident fix or not."

"Installed new part, all ops good. Job complete.

Was able to realign hose that detattached correctly and confirmed unit after running awhile no leaks

Installed new control and comfirned unit quiet and opperating like it should and customer is happy

Removed and replaced parts all ops test ok

"Installed new icemaker and also removed all the ice buildup from the freezer floor and defrost drainage pipe. Icemaker is now working properly,y without any water leaks. Job complete.

"Got under the unit to start disassembly and found the center bolt, for the rotor, had fallen completely out and was laying on the floor. Installed new slider kit and confirm bolt secured in place. Performed calibration and auto test and confirmed all ops functioning properly. Job complete.

"Installed new icemaker in top freezer fridge due to no ice,condominium being renovated and water is off,I left icemaker shut off arm up"

Unit needs new suspension and gearcase. Customer decided to replace unit. Job complete.

Found spring link off from hinge do to installation reinstalled hinge all ops test ok

Removed and replaced parts listed all ops test ok cleared codes customer to advise.

Installed cook top checked ok

"wash motor is bad , it's filling fine and motor runs but no pressure out of it wash motor is discontinued ,NO FIX

Range console bad error code f2e1 customer to buy new

All frost development since initial service thawed from the units evaporator. New defrost heater element and control box installed. Unit ran through both diagnostic testing and normal cooling operation without fault. All unit operations check good upon completion of service. Customer to advise.

Frame warped unit non repairable sr#7739767230

Installed new capacitor. Tested operation of the unit and it is now working properly. Job complete.

Installed checked ok

replaced all parts listed and

"Found the units drive motor failed, unable to achieve rotation of the drum without manual assistance, overheating strong electrical burning odor. Additionally, found excessive slack of the door switch, prelude to failure. Due to primary failure and unit condition as a result of environment age and normal use, no less than a new drive motor, blower wheel, dryer maintenance kit including new roller supports idler wheel and drive belt will be needed to correct. Installation of a new door switch would also be advised. Additional component issues and/or failures may be found through disassembly. Due to the unit age, condition and expected cost to repair the customer has opted not to advance with further service at this time. Service complete."

We removed and replaced the Magnatron capacitor and diode. Unit was very tight installation vented outdoors. Insured ventilation was connected back properly and properly sealed with a aluminum foil tape. All functions now check OK. Job complete.

"Found water valve leaking into icemaker, causing the fill tube to freeze in a block of ice and the demise of the icemaker. I removed and replaced the faulty water valve. I then used my steamer to clear the fill tube That was solid. I removed and replaced the icemaker. Ran the icemaker diagnostics check temperature and all functions check OK. Job complete.

Installed checked ok

"Got to this unit to find it not responding to starting cycles not responding to diagnostics was unable to run any sort of testing. Unit would not fill with water drain water, agitate or spin. Was at some point during the trials able to get into the diagnostics. And was having lots of issues trying to get any functions to work correctly. Tried resetting the computer tried calibrations diagnostics and individual parts to turn on and off. None of this was fruitful. Had to start looking at all components and electronic parts to confirm visual inspection and no visible issues. Started at the top and worked my way down. Was unable to find any discrepancies with the wiring in the top end. All plugs were connected securely. Further investigation on the bottom of the unit all wires to be intact and no visible issues found. Checking further found that the plug had come out of the drain pump itself. With the drain pump plug out of the drain pump this unit would not move forward during any testing. Once this was plugged back in was able to run diagnostics and get all portions and parts of this unit to be working correctly now. Ran enough testing to make me feel comfortable and leaving this unit this way. The drain pump electrical plug was secure when plugged back in. It is unclear how this occurred but the unit is now working correctly. job complete.

Got back to this unit unit and was able to install new door tested operation of door and remove plastic. Put new handle on connected properly. All parts and pieces appear to be working correctly. No further issues found at this time. Job complete.